PIC18F26K22-I/SO Microchip Technology, PIC18F26K22-I/SO Datasheet - Page 341

• Manufacturer Part Number: PIC18F26K22-I/SO
• Description: IC PIC MCU 64KB FLASH 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K22-I/SO

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (0.300", 7.50mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 1KB
• Ram Memory Size: 3896Byte
• Cpu Speed: 64MHz
• No. Of Timers: 7
• Processor Series: PIC18F
• Core: PIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.0
The Digital-to-Analog Converter supplies a variable
voltage reference, ratiometric with the input source,
with 32 selectable output levels.
The input of the DAC can be connected to:
• External V
• V
• FVR (Fixed Voltage Reference)
The output of the DAC can be configured to supply a
reference voltage to the following:
• Comparator positive input
• ADC input channel
• DACOUT pin
The Digital-to-Analog Converter (DAC) can be enabled
by setting the DACEN bit of the VREFCON1 register.
22.1
The DAC has 32 voltage level ranges. The 32 levels
are set with the DACR<4:0> bits of the VREFCON2
register.
The DAC output voltage is determined by the following
equations:
EQUATION 22-1:
22.2
The DAC output value is derived using a resistor ladder
with each end of the ladder tied to a positive and
negative voltage reference input source. If the voltage
of either input source fluctuates, a similar fluctuation will
result in the DAC output value.
The value of the individual resistors within the ladder
can
Characteristics”.
22.3
In order for the DAC module to consume the least
amount of power, one of the two voltage reference input
sources to the resistor ladder must be disconnected.
Either the positive voltage source, (V
negative voltage source, (V
 2010 Microchip Technology Inc.
V
DD
V
V
SRC
SRC
OUT
supply voltage
be
+ = V
- = V
DIGITAL-TO-ANALOG
CONVERTER (DAC) MODULE
Output Voltage Selection
Ratiometric Output Level
Low-Power Voltage State
=


REF
found

V
DD
SS
SRC
or V
, V
pins
+ V
REF
REF
–
+ or FVR1
in
DAC OUTPUT VOLTAGE
-
SRC
-

Section 27.0
SRC

DACR<4:0>
------------------------------ -
-) can be disabled.
2 5
SRC


+ V
“Electrical
+), or the
SRC
-
Preliminary
The negative voltage source is disabled by setting the
DACLPS bit in the VREFCON1 register. Clearing the
DACLPS bit in the VREFCON1 register disables the
positive voltage source.
22.4
The DAC output voltage can be set to V
least amount of power consumption by performing the
following:
• Clearing the DACEN bit in the VREFCON1
• Setting the DACLPS bit in the VREFCON1
• Configuring the DACPSS bits to the proper
• Configuring the DACRx bits to ‘11111’ in the
This is also the method used to output the voltage level
from the FVR to an output pin. See Section 22.6 “DAC
Voltage Reference Output” for more information.
22.5
The DAC output voltage can be set to V
least amount of power consumption by performing the
following:
• Clearing the DACEN bit in the VREFCON1
• Clearing the DACLPS bit in the VREFCON1
• Configuring the DACPSS bits to the proper
• Configuring the DACRx bits to ‘00000’ in the
This allows the comparator to detect a zero-crossing
while not consuming additional current through the DAC
module.
22.6
The DAC can be output to the DACOUT pin by setting
the DACOE bit of the VREFCON1 register to ‘1’.
Selecting the DAC reference voltage for output on the
DACOUT pin automatically overrides the digital output
buffer and digital input threshold detector functions of
that pin. Reading the DACOUT pin when it has been
configured for DAC reference voltage output will always
return a ‘0’.
Due to the limited current drive capability, a buffer must
be used on the DAC voltage reference output for
external connections to DACOUT. Figure 22-2 shows
an example buffering technique.
register.
register.
positive source.
VREFCON2 register.
register.
register.
negative source.
VREFCON2 register.
PIC18(L)F2X/4XK22
Output Clamped to Positive
Voltage Source
Output Clamped to Negative
Voltage Source
DAC Voltage Reference Output
DS41412A-page 341
SRC
SRC
+ with the
- with the