10054542-001LF FCI, 10054542-001LF Datasheet - Page 5

• Manufacturer Part Number: 10054542-001LF
• Description: CONN RECEPT SAS 22POS VERT PCB
• Manufacturer: FCI

Specifications of 10054542-001LF

• Connector Style: Receptacle
• Connector Type: SAS
• Number Of Positions: 22
• Mounting Type: Through Hole
• Termination: Solder
• Contact Finish: Gold
• Contact Finish Thickness: 3µin (0.08µm)
• Product: SAS Connectors
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 609-1549

6.0
NUMBER
TITLE
Copyright
Form E-3334
Rev F
6.1
6.2
6.3
6.4
6.5
MECHANICAL CHARACTERISTICS
GS-12-239
FCI
Perform in accordance with EIA 364-13B. The force to mate a receptacle connector and compatible
Perform in accordance with EIA 364-05B. Fully populated connectors shall be applied to test boards with
a. Force to insert one straight or right angle header pin: 40 N maximum
b. Force to insert one right angle receptacle pin: 40 N maximum
c. Force to insert one straight receptacle or orthogonal header pin: 25 N maximum
d. Number of readings: 1 per connector assembly tested
e. Number of connectors to be tested: 13 sets (3 sets in minimum holes; 5 sets in nominal holes; 5 sets
Perform in accordance with EIA 364-05B. Fully populated connectors shall be removed from test boards
a. Force to remove one straight or right angle header pin: 7 N minimum
b. Force to remove one right angle receptacle pin: 7 N minimum
c. Force to remove one straight receptacle or orthogonal header pin: 3 N minimum
d. Number of connectors to be tested: 13 sets (3 sets in minimum holes; 5 sets in nominal holes; 5 sets
Perform in accordance with Telcordia GR-1217-CORE, November 1995, Section 5.1.7. Use test boards
Perform in accordance with Telcordia GR-1217-CORE, November 1995, Section 5.1.7. Use test boards
Mating / Un-mating Force
header shall not exceed 0.45 N per contact (0.60 N per orthogonal contact). The un-mating force shall
not be less than 0.15 N per contact. The following details shall apply:
a.
b.
c.
d.
e.
Compliant pin insertion force
minimum, maximum, and nominal size plated through holes (as defined in Table 2) using an electric
application press and FCI recommended application tooling. The following details shall apply:
Compliant pin retention force
with minimum, maximum, or nominal size plated through holes (as defined in Table 2) using an electric
application press and FCI recommended removal tooling. The following details shall apply:
PCB Hole Deformation Radius
with minimum diameter plated through holes. Make cross-sections 0.25mm (0.010 inch) from the top
board surface and near the center of the press-fit section. Photograph and measure the minimum copper
thickness remaining between the compliant pin and the printed wiring board laminate and the hole
deformation radius. The minimum average copper thickness remaining between the compliant pin and
the printed wiring board laminate shall not be less than 7.5 µm (0.0003”). The maximum average hole
deformation radius shall be no greater than 37.5 µm (0.0015”). The maximum hole deformation radius
reading must not exceed 50 µm (0.0020”). Test 15 holes.
PCB Hole Wall Damage
with minimum diameter plated through holes. Cross-section perpendicular to the board surface and
through the compliant section wear track. There shall be no copper cracks, separations between
conductive interfaces, or laminate-to-copper separations. Test 15 pins.
AirMax VS
in maximum holes)
in maximum holes)
Cross head speed: 1 inch per minute
Lubrication: None
Utilize free-floating fixtures
Number of mate/un-mate cycles: 3
Number of mated connector pairs to be tested: 10
TYPE
®
Connector System, press-fit products
PRODUCT SPECIFICATION
PDM: Rev:F
STATUS:
PAGE
AUTHORIZED BY
STATUS
Tan Chen Hong
Released
5 of 11
UNRESTRICTED
Printed: Oct 04, 2008
REVISION
DATE
GS-01-001
30 Sep 08
F
.