ADSP-21061LKSZ-176 Analog Devices Inc, ADSP-21061LKSZ-176 Datasheet - Page 25

• Manufacturer Part Number: ADSP-21061LKSZ-176
• Description: ADSP-21061L 44Hz, 3V SHARC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21061LKSZ-176

• Interface: Synchronous Serial Port (SSP)
• Clock Rate: 44MHz
• Non-volatile Memory: External
• On-chip Ram: 128kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 240-MQFP, 240-PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Memory Read—Bus Master
Use these specifications for asynchronous interfacing to memo-
ries (and memory-mapped peripherals) without reference to
CLKIN. These specifications apply when the ADSP-21061 is the
Table 12. Memory Read—Bus Master
1
2
3
4
Parameter
Timing Requirements
t
t
t
t
t
t
Switching Characteristics
t
t
t
t
t
W = (number of wait states specified in WAIT register)
HI = t
H = t
Data delay/setup: user must meet t
The falling edge of MSx, SW, BMS is referenced.
Data hold: user must meet t
ACK delay/setup: user must meet t
DAD
DRLD
HDA
HDRH
DAAK
DSAK
DRHA
DARL
RW
RWR
SADADC
and dc loads.
for assertion of ACK (High).
CK
CK
(if an address hold cycle occurs as specified in WAIT register; otherwise H = 0).
(if an address hold cycle or bus idle cycle occurs, as specified in WAIT register; otherwise HI = 0).
ADDRESS
MSX, SW
WR, DMAG
ADDRCLK
BMS
(OUT)
DATA
ACK
RD
Address, Selects Delay to Data Valid
RD Low to Data Valid
Data Hold from Address, Selects
Data Hold from RD High
ACK Delay from Address, Selects
ACK Delay from RD Low
Address, Selects Hold After RD High
Address, Selects to RD Low
RD Pulse Width
RD High to WR, RD, DMAGx Low
Address, Selects Setup Before ADRCLK High
HDA
or t
DAD
HDRH
DAAK
t
or t
SADADC
or synchronous spec t
or t
DRLD
DSAK
t
DARL
or synchronous spec t
t
or synchronous specification t
DAAK
1
4
3
2
t
HSDATI
DSAK
3
Figure 14. Memory Read—Bus Master
2, 4
t
DAD
Rev. C | Page 25 of 56 | July 2007
. See
1, 2
SSDATI
t
CK
Example System Hold Time Calculation on Page 44
t
DRLD
.
.
2
SACKC
(Table 13 on Page
t
RW
bus master accessing external memory space in asynchronous
access mode. Note that timing for ACK, DATA, RD, WR, and
DMAGx strobe timing parameters only applies to asynchronous
access mode.
26) for deassertion of ACK (Low), all three specifications must be met
Min
0.5
2.0
0+H
2 + 3DT/8
12.5 + 5DT/8 + W
8 + 3DT/8 + HI
0 + DT/4
ADSP-21061/ADSP-21061L
for the calculation of hold times given capacitive
5 V and 3.3 V
t
HDRH
t
t
HDA
DRHA
t
RWR
Max
18 + DT+W
12 + 5DT/8 + W
15 + 7DT/8 + W
8 + DT/2 + W
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns