SLATAFL6GBJI STEC, SLATAFL6GBJI Datasheet - Page 36

• Manufacturer Part Number: SLATAFL6GBJI
• Manufacturer: STEC
• Type: ATA Cardr

Specifications of SLATAFL6GBJI

• Density: 6GByte
• Operating Supply Voltage (typ): 3.3/5V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Package Type: Not Required
• Mounting: Socket
• Pin Count: 68
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 3.18/4.75V
• Operating Supply Voltage (max): 3.465/5.25V
• Programmable: Yes
• Lead Free Status / Rohs Status: Not Compliant

SimpleTech P/N:
(where xxx=capacity; U=RoHS compliant lead-free; I=Ind. Op. Temp;
F=fixed device; S=small data packet optimized)
Check Power Mode
(code: E5h or 98h)
This command checks the power mode.
Execute Drive Diagnostic
(code: 90h)
This command performs the internal diagnostic tests
implemented by the card. See ERROR register for dianostic
codes.
Erase Sector(s)
(code: C0h)
This command is used to pre-erase and condition data
sectors in advance.
Format Track
(code: 50h)
This command writes the desired head and cylinder of the
selected drive with a vender unique data pattern (typically
00h or FFh). This card accepts a sector buffer of data from the
host to follow the command with the same protocol as the
Write Sector Command although the information in the
buffer is not used.
Identify Drive
(code: ECh)
This command enables the host to receive parameter
information from the card. (See tables on the next page.)
Idle
(code: E3h or 97h)
This command causes the card to set BSY, enter the Idle
mode, clear BSY, and generate an interrupt. If the sector
count is non-zero, automatic power down mode is enabled.
If the sector count is zero, the automatic power down
mode is disabled.
Idle Immediate
(code: E1h or 95h)
This command causes the card to set BSY, enter the Idle
(Read) mode, clear BSY, and generate an interrupt.
Initialize Drive Parameters
(code: 91h)
This command enables the host to set the number of
sectors per track and the number of heads per cylinder.
SLATAFLxxxJ(U)(I)-(F)(S)
Document Part Number 61000-02810-110 July 2005
Read Buffer
(code: E4h)
This command enables the host to read the current
contents of the card’s sector buffer.
Read Multiple
(code: C4h)
This command performs similarly to the Read Sectors
command. Interrupts are not generated on each sector,
but on the transfer of a block which contains the number of
sectors defined by a Set Multiple command.
Read Long Sector
(code: 22h or 23h)
This command performs similarly to the Read Sector(s)
command except that it returns 516 bytes of data instead
of 512 bytes.
Read Sector(s)
(code: 20h or 21h)
This command reads from 1 to 256 sectors as specified in
the Sector Count register. A sector count of 0 requests 256
sectors. The transfer begins at the sector specified in the
Sector Number register.
Read Verify Sector(s)
(code: 40h or 41h)
This command verifies one or more sectors on the card by
transferring data from the flash media to the data buffer in
the card and verifying that the ECC is correct. This
command is identical to the Read Sectors command,
except that DRQ is never set and no data is transferred to
the host.
Recalibrate
(code: 1Xh)
The card performs only the interface timing and register
operations. When this command is issued, the card sets
BSY and waits for an appropriate length of time after
which it clears BSY and issues an interrupt. When this
command ends normally, the card is initialized.
PC CARD
Page 36