SLATAFL6GBJI STEC, SLATAFL6GBJI Datasheet - Page 42

• Manufacturer Part Number: SLATAFL6GBJI
• Manufacturer: STEC
• Type: ATA Cardr

Specifications of SLATAFL6GBJI

• Density: 6GByte
• Operating Supply Voltage (typ): 3.3/5V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Package Type: Not Required
• Mounting: Socket
• Pin Count: 68
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 3.18/4.75V
• Operating Supply Voltage (max): 3.465/5.25V
• Programmable: Yes
• Lead Free Status / Rohs Status: Not Compliant

SimpleTech P/N:
(where xxx=capacity; U=RoHS compliant lead-free; I=Ind. Op. Temp;
F=fixed device; S=small data packet optimized)
REVISION HISTORY
Rev.
-101 2/1/04. Initial Release.
-102 5/26/04. Sleep mode current at 3.3V corrected to
-103 6/18/04. Features bullets on page 1 updated. Pin
SimpleTech Inc. reserves the right to make changes to specifications and product descriptions such as but not limited to numbers,
parameters and other technical information contained herein without notice. Contact SimpleTech Inc. sales office to obtain the latest
specifications. SimpleTech Inc. grants no warranty with respect to this Data Sheet, neither explicit nor implied, and it is not liable for
direct or indirect damages. Some States do not grant the exclusion of incidental damages and as such this statement may not be valid in
such states. The provisions of this Data Sheet do not convey to the purchaser of the device any license under any patent rights or other
intellectual property rights of SimpleTech Inc. or others.
Change Description from Previous Revision
80µA from 80mA. The operating current at 3.3V
corrected to 30mA from 3mA. IOL/IOH condition at
5.0V is removed. Showpiece photo replaces Block
Diagram. General Description updated with new
marketing copy. R/W speeds updated from 5.4/5.5MB/
s to 5/5MB/s. 64MB option removed. CHS Parameter
table added. VCC(min) changed to 3.18V from
3.135V. VCC 5V tolerance changed to 5% from 10%.
Preliminary notice removed. Disclaimer notice added.
CIS Information corrected.
Assignments for IDE Mode corrected to indicate
which pins are not used in IDE Mode. . Pin
Description changes: -CD1 and -CD2 not used in IDE
mode; -IOIS16 not used in IDE mode; -WAIT
description corrected to not used by card and pulled
up by 4.7K ohm resistor. Performance rates for read
and write described as sustained read and sustained
write. AC Characteristics VCC 3.3V operating
tolerances restated as +5% and -3.6% tolerances.
Error register bit 0 Function “not supported” phrase
removed. DMA commands removed. (Paper only error
indicated that DMA was supported). Identify Drive
Information table updated to reflect DMA not
supported. “-F” p/n suffix selection added to notes of
the Ordering Information. ATA-4 compatiblility added
to Features. DC Characterists Sleep Mode values
changed from 80uA to 800uA for 3.3V power supply,
and 120uA to 1200uA for 5V power supply.
SLATAFLxxxJ(U)(I)-(F)(S)
Document Part Number 61000-02810-110 July 2005
-104 7/9/04. Endurance increased from 300,000 cycles
-105 7/22/04. “up to” added to sustained read and write
-106 8/23/04. Definition for Serial #, Firmware Rev., and
-107 10/14/04. Standard ECC, Endurance, and Warranty
-108 2/14/05. Shock parameter changed to 0.330ms to
-109 2/14/05. MWDMA Mode 2 support added for this rev of
-110 7/20/05. Separate shock and vibration for U option
min to 2 million cycles min.
data rate performance.
Model # in the Identify Drive Information table added
in callout. Words 0, 4-5, 20-21, 49 and 63 of Drive ID
table corrected.
bullets added to Features on page 1.
0.750ms from 11ms. 3/14/05. Humidity parameter
updated to 95% from 85%. CHS values updated.
4/22/05. U and S options added.
spec only. 3/14/05. Humidity parameter updated to
95% from 85%. CHS values updated. 4/22/05. S and
U options added. 7/20/05. For higher revs of this
spec, the MWDMA support has been removed.
Product with MWDMA has been given a P/N of
SLATAFLxxxJ2(U)(I)-(F)(S).
added.
PC CARD
Page 42