AT94K05AL-25AQU Atmel, AT94K05AL-25AQU Datasheet - Page 14

• Manufacturer Part Number: AT94K05AL-25AQU
• Description: IC FPSLIC 5K GATE 25MHZ 100-TQFP
• Manufacturer: Atmel
• Series: FPSLIC®r

Specifications of AT94K05AL-25AQU

• Core Type: 8-bit AVR
• Speed: 25MHz
• Interface: I²C, UART
• Program Sram Bytes: 4K-16K
• Fpga Sram: 2kb
• Data Sram Bytes: 4K ~ 16K
• Fpga Core Cells: 256
• Fpga Gates: 5K
• Fpga Registers: 436
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: ATSTK594 - BOARD FPSLIC DAUGHTER FOR STK500
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

2.10
14
Clocking and Set/Reset
AT94KAL Series FPSLIC
Six of the eight dedicated Global Clock buses (1, 2, 3, 4, 7 and 8) are connected to a dual-use
Global Clock pin. In addition, two Global Clock buses (5 and 6) are driven from clock signals
generated within the AVR microcontroller core, see
An FPGA core internal signal can be placed on any Global Clock bus by routing that signal to a
Global Clock access point in the corners of the embedded core. Each column of the array has a
Column Clock selected from one of the eight Global Clock buses. The left edge Column Clock
mux has two additional inputs from dual-use pins FCK1, see
fast clocking to left-side I/O. Each sector column of four cells can be clocked from a (Plane 4)
express bus or from the Column Clock. Clocking to the 4 cells of a sector can be disabled. The
Plane 4 express bus used for clocking is half length at the array edge. The clock provided to
each sector column of four cells can be either inverted or not inverted. The register in each cell is
triggered on a rising clock edge. On power-up, constant “0” is provided to each register’s clock
pins. A dedicated Global Set/Reset bus, see
except those used for clocking, Global or Fast. An internal signal can be placed on the Global
Set/Reset bus by routing that signal to the pad programmed as the Global Set/Reset input. Glo-
bal Set/Reset is distributed to each column of the array. Each sector column of four cells can be
Set/Reset by a (Plane 5) express bus or by the Global Set/Reset. The Plane 5 express bus used
for Set/Reset is half length at array edge. The Set/Reset provided to each sector column of four
cells can be either inverted or not inverted. The function of the Set/Reset input of a register
(either Set or Reset) is determined by a configuration bit for each cell. The Set/Reset input of a
register is Active Low (logic 0). Setting or resetting of a register is asynchronous. On power-up, a
logic 1 (High) is provided by each register, i.e., all registers are set at power-up.
Figure 2-9.
CORE GCK6
TO FPGA
FPGA Clocks from AVR
CORE GCK5
TO FPGA
GCK6
AVR SYSTEM
(AVR CLK)
Figure
CLOCK
AVR SYSTEM CLOCK (AVR CLK)
TIMER OSC TOSC1 (AS2 SET IN ASSR)
WATCHDOG CLOCK
"1"
Figure
2-7, can be driven by any USER I/O pad,
2-9.
Figure
2-6, and FCK2 to provide
1138I–FPSLI–1/08