20-101-1196 Rabbit Semiconductor, 20-101-1196 Datasheet - Page 32
20-101-1196
Manufacturer Part Number
20-101-1196
Description
MODULE RABBITCORE RCM3900
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1196.pdf
(168 pages)
Specifications of 20-101-1196
Module/board Type
MPU Core Module
For Use With/related Products
RCM3900
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
20-101-1196
316-1155
316-1155
- Current page: 32 of 168
- Download datasheet (3Mb)
4.1.1 Memory I/O Interface
The Rabbit 3000 address lines (A0–A18) and all the data lines (D0–D7) are routed
internally to the onboard flash memory and SRAM chips. I/O write (/IOWR) and I/O read
(/IORD) are available for interfacing to external devices—pay attention to the loading on
these two signals if you use them since these signals are also used by the RCM3900.
Parallel Port A can also be used as an external I/O data bus to isolate external I/O from the
main data bus. Parallel Port B pins PB2–PB7 can also be used as an auxiliary address bus.
When using the external I/O bus for a digital output or the LCD/keypad module on the
Prototyping Board, or for any other reason, you must add the following line at the begin-
ning of your program.
#define PORTA_AUX_IO
// required to enable auxiliary I/O bus
4.1.2 LEDs
The RCM3900 has three Ethernet status LEDs located beside the RJ-45 Ethernet jack—
these are discussed in Section 4.2.2.
Additionally, there is one dual LED DS4. PD1 on the Rabbit 3000’s Parallel Port D is used
to enable the NAND flash on the RCM3900 model, but is connected to the green CE LED
at DS4, which is not used. The red BSY LED at DS4 is a user-programmable LED, and is
controlled by PD0. The
and
sample programs in the
CONTROLLEDS.C
FLASHLEDS.C
Dynamic C
folder show how to set up and use this user-
SAMPLES\RCM3900
programmable LED.
4.1.3 Other Inputs and Outputs
The status, /RESET_IN, SMODE0, and SMODE1 I/O are normally associated with the
programming port. Since the status pin is not used by the system once a program has been
downloaded and is running, the status pin can then be used as a general-purpose CMOS
output. The programming port is described in more detail in Section 4.2.3.
/RESET_IN is an external input used to reset the Rabbit 3000 microprocessor and the
RCM3900 onboard peripheral circuits. /RES is an output from the reset circuitry that can
be used to reset external peripheral devices.
RabbitCore RCM3900 User’s Manual
32
Related parts for 20-101-1196
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: