CS42L51-CNZ Cirrus Logic Inc, CS42L51-CNZ Datasheet - Page 36

• Manufacturer Part Number: CS42L51-CNZ
• Description: IC CODEC STEREO W/HDPN AMP 32QFN
• Manufacturer: Cirrus Logic Inc
• Type: Stereo Audior

Specifications of CS42L51-CNZ

• Package / Case: 32-QFP
• Data Interface: PCM Audio Interface
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 98 / 98
• Voltage - Supply, Analog: 1.8V, 2.5V
• Voltage - Supply, Digital: 1.8V, 2.5V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 6
• Number Of Dac Outputs: 2
• Conversion Rate: 96 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, I2C, SPI)
• Resolution: 24 bit
• Operating Supply Voltage: 1.8 V / 2.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 2 ADC/2 DAC
• Thd Plus Noise: - 88 dB ADC / - 86 dB DAC
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1005 - BOARD EVAL FOR CS42L51 CODEC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1045

36
4.4.5
4.4.6
BPVOL[4:0]
Tone Control
Shelving filters are used to implement bass and treble (boost and cut) with four selectable corner frequen-
cies. Boosting will affect peak detect and limiting when levels exceed the maximum threshold settings.
Limiter
When enabled, the limiter monitors the digital input signal before the DAC modulator, detects when levels
exceed the maximum threshold settings and lowers the AOUT volume at a programmable attack rate be-
low the maximum threshold. When the input signal level falls below the maximum threshold, the AOUT
volume returns to its original level set in the Volume Control register at a programmable release rate. At-
tack and release rates are affected by the DAC soft ramp/zero cross settings and sample rate, Fs. Limiter
soft ramp and zero cross dependency may be independently enabled/disabled.
Recommended settings: Best limiting performance may be realized with the fastest attack and slowest
release setting with soft ramp enabled in the control registers. The “cushion” bits allow the user to set a
threshold slightly below the maximum threshold for hysteresis control - this cushions the sound as the lim-
iter attacks and releases.
Note:
1. When the Limiter is enabled, the AOUT Volume is automatically controlled and should not be adjusted
2. The Limiter maintains the output signal between the CUSH and MAX thresholds. As the digital input
Software
Controls:
Software
Controls:
manually. Alternative volume control may be realized using the PCMMIXx_VOL[6:0] bits.
signal level changes, the level-controlled output may not always be the same but will always fall within
the thresholds.
REPEAT = '1'
BEEP = '1'
REPEAT = '1'
BEEP = '0'
REPEAT = '0'
BEEP = '1'
FREQ[3:0]
“Tone Control (Address 15h)” on page
“Limiter Release Rate Register (Address 1Ah)” on page
1Bh)” on page
CONTINUOUS BEEP: Beep turns on at a configurable frequency (FREQ) and volume (BPVOL) and remains
on until REPEAT is cleared.
MULTI-BEEP: Beep turns on at a configurable frequency (FREQ)
and volume (BPVOL) for the duration of ONTIME and turns off for
the duration of OFFTIME. On and off cycles are repeated until
REPEAT is cleared.
SINGLE-BEEP: Beep turns on at a
configurable frequency (FREQ) and
volume (BPVOL) for the duration of
ONTIME. BEEP must be cleared
and set for additional beeps.
ONTIME[3:0]
Figure 15. Beep Configuration Options
70,
“DAC Control (Address 09h)” on page 58
OFFTIME[2:0]
65.
69,
“Limiter Attack Rate Register (Address
...
CS42L51
DS679F1