MXB7846EEE+T Maxim Integrated Products, MXB7846EEE+T Datasheet - Page 11

• Manufacturer Part Number: MXB7846EEE+T
• Description: IC CNTRLR TOUCH RES 16QSOP
• Manufacturer: Maxim Integrated Products
• Type: Temperature Sensorr

Specifications of MXB7846EEE+T

• Input Type: Analog
• Output Type: Digital
• Interface: 4-Wire
• Current - Supply: 950µA
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The ADCs input tracking circuitry has a 25MHz small-
signal bandwidth, so it is possible to digitize high-
speed transient events. To avoid high-frequency sig-
nals being aliased into the frequency band of interest,
anti-alias filtering is recommended.
Internal protection diodes, which clamp the analog input
to V
from GND - 0.3V to V
inputs must not exceed V
lower than GND by more than 50mV for accurate con-
version. If an off-channel analog input voltage exceeds
the supplies, limit the input current to 50mA. The analog
input pins are ESD protected to ±8kV using the Contact
Discharge method and ±15kV using the Air-Gap
method specified in IEC 61000-4-2.
The MXB7846 provides two conversion methods—differ-
ential and single ended. The SER/DFR bit in the control
word selects either mode. A logic 1 selects a single-
ended conversion, while a logic 0 selects a differential
conversion.
Changes in operating conditions can degrade the accu-
racy and repeatability of touch-screen measurements.
Therefore, the conversion results representing X and Y
coordinates may be incorrect. For example, in single-
ended measurement mode, variation in the touch-screen
driver voltage drops results in incorrect input reading.
Differential mode minimizes these errors.
Figure 3 shows the switching matrix configuration for
Y-coordinate measurement in single-ended mode. The
MXB7846 measures the position of the pointing device
by connecting X+ to IN+ of the ADC, enabling Y+ and
Y- drivers, and digitizing the voltage on X+. The ADC
performs a conversion with REF+ = REF and REF- =
GND. In single-ended measurement mode, the bias to
the touch screen can be turned off after the acquisition
to save power. The on-resistance of the X and Y drivers
results in a gain error in single-ended measurement
mode. Touch-screen resistance ranges from 200Ω to
900Ω (depending on the manufacturer), whereas the
on-resistance of the X and Y drivers is 8Ω (typ). Limit
the touch-screen current to less than 50mA by using a
touch screen with a resistance higher than 100Ω. The
with Internal Reference and Temperature Sensor
2.375V to 5.25V, 4-Wire Touch-Screen Controller
DD
and GND, allow the analog input pins to swing
Input Bandwidth and Anti-Aliasing
______________________________________________________________________________________
DD
Touch-Screen Conversion
+ 0.3V without damage. Analog
Analog Input Protection
Differential vs. Single Ended
DD
by more than 50mV or be
Single-Ended Mode
resistive-divider created by the touch screen and the
on-resistance of the X and Y drivers result in both an
offset and a gain shift. Also, the on-resistance of the X
and Y drivers does not track the resistance of the touch
screen over temperature and supply. This results in fur-
ther measurement errors.
Figure 4 shows the switching matrix configuration for
Y-coordinate measurement. The REF+ and REF- inputs
are connected directly to the Y+ and Y- pins, respec-
tively. Differential mode uses the voltage at the Y+ pin
as the REF+ voltage and voltage at the Y- pin as REF-
voltage. This conversion is ratiometric and independent
of the voltage drop across the drivers and variation in
the touch-screen resistance. In differential mode, the
touch screen remains biased during the acquisition and
conversion process. This results in additional supply
current and power dissipation during conversion when
compared to the absolute measurement mode.
Figure 5 shows the block diagram for the PENIRQ func-
tion. When used, PENIRQ requires a 10kΩ to 100kΩ
pullup to +V
the touch screen is touched. The PENIRQ output can
be used to initiate an interrupt to the microprocessor,
which can write a control word to the MXB7846 to start
a conversion.
Figure 6 shows the timing diagram for the PENIRQ pin
function. The diagram shows that once the screen is
touched while CS is high, the PENIRQ output goes low
after a time period indicated by t
value changes for different touch-screen parasitic
capacitance and resistance. The microprocessor
receives this interrupt and pulls CS low to initiate a con-
version. At this instant, the PENIRQ pin should be
masked, as transitions can occur due to a selected
input channel or the conversion mode. The PENIRQ pin
functionality becomes valid when either the last data bit
is clocked out, or CS is pulled high.
The MXB7846 provides two methods for measuring the
pressure applied to the touch screen (Figure 7). By
measuring R
between a finger or stylus in contact with the touch
screen. Although 8-bit resolution is typically sufficient,
the following calculations use 12-bit resolution demon-
strating the maximum precision of the MXB7846.
DD
TOUCH
. If enabled, PENIRQ goes low whenever
Touch-Pressure Measurement
PEN Interrupt Request (PENIRQ)
, it is possible to differentiate
Differential Measurement Mode
TOUCH
. The t
TOUCH
11