TLE6240GPNT Infineon Technologies, TLE6240GPNT Datasheet
TLE6240GPNT
Specifications of TLE6240GPNT
Related parts for TLE6240GPNT
TLE6240GPNT Summary of contents
Page 1
... Smart 16-Channel Low-Side Switch coreFLEX Rev.3.3, 2010-02- ...
Page 2
... Example for an access to channel 6.2 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.2.1 Diagnosis Read-out options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7 Application Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.1 Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.2 Engine Management Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.3 Daisy Chain Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Data Sheet Smart 16-Channel Low-Side Switch 2 TLE6240GP Table of Contents V3.3, 2010-02-15 ...
Page 3
... Solenoids, Relays and Resistive Loads General Description 16-fold Low-Side Switch in Smart Power Technology (SPT) with a Serial Peripheral Interface (SPI) and 16 open drain DMOS output stages. The TLE6240GP is protected by embedded protection functions and designed for automotive and industrial applications. The output stages are controlled via SPI Interface. Additionally 8 channels can be controlled direct in parallel for PWM applications ...
Page 4
... Drain source clamping voltage On resistance Nominal Output current (channel Nominal Output current (channel 9 - 16) Minimum Output current Limit (channel Minimum Output current Limit (channel 9 - 16) Block Diagram Figure 1 Application Block Diagram Data Sheet Smart 16-Channel Low-Side Switch Symbol Value V 4.5 … 5 .... 60 DS(AZ)max R 2.2 ON1-8 (max @ 150° ...
Page 5
... AND - operated with the respective SPI data bit. This boolean operation can be programmed via SPI control byte (see Chapter 5). The SPI interface also performs a diagnostic information for each channel. Data Sheet Smart 16-Channel Low-Side Switch 5 TLE6240GP Block Diagram Rev.3.3, 2010-02-15 ...
Page 6
... IN4 13 IN4 IN9 I OUT3 14 OUT3 OUT6 I OUT4 15 OUT4 OUT5 I OUT11 16 OUT11 OUT14 I OUT12 17 OUT12 OUT13 V OUT12 18 GND GND 6 TLE6240GP Smart 16-Channel Low-Side Switch Block Diagram V Batt 36 I OUT16 V OUT4 35 I OUT15 34 I OUT8 V IN4 33 I OUT IN12 V IN12 31 I IN11 V IN11 30 ...
Page 7
... Power Output Channel 10 4 OUT1 Power Output Channel 1 5 OUT2 Power Output Channel 2 6 IN1 Input Channel 1 7 IN2 Input Channel Supply Voltage S 9 RESET Reset 10 CS Chip Select Data Sheet Smart 16-Channel Low-Side Switch PG-DSO- DSO-36(Power )_TLE6240.vsd 7 TLE6240GP Pin Configuration ...
Page 8
... Input Channel 12 32 OUT7 Power Output Channel 7 33 OUT8 Power Output Channel 8 34 OUT15 Power Output Channel 15 35 OUT16 Power Output Channel 16 36 GND Ground Heat Slug internally connected to ground pins Data Sheet Smart 16-Channel Low-Side Switch 8 TLE6240GP Pin Configuration Rev.3.3, 2010-02-15 ...
Page 9
... Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data Sheet Smart 16-Channel Low-Side Switch Maximum Ratings and Operating Conditions Symbol Limit Values Min ...
Page 10
... Maximum Ratings and Operating Conditions Symbol Min -55 stg E – – tot Symbol Min. R – thJSp 1) R Figure 5 ); all – thjA 10 TLE6240GP Smart 16-Channel Low-Side Switch Limit Values Unit Conditions Typ. Max. °C – 150 – °C – 150 – T – D1-8 I D9-16 T 3.3 – ...
Page 11
... Dimensions: 76.2 x 114.3 x 1.5 mm³ ; Material: FR4 Thermal Vias: diameter= 0.3 mm; plating 25 µm; 61 pcs. Metalization accodring: JEDEC 2s2p (JESD 51-7) + (JESD 51-5) Figure 5 Thermal Simulation - PCB set-up Data Sheet Smart 16-Channel Low-Side Switch Maximum Ratings and Operating Conditions 70µm modeled (traces) 35µm, 90% metalization 35µm, 90% metalization 70µm, 5% metalization Thermal_Setup ...
Page 12
... Power Supply & Reset RESET - Reset pin. If the reset pin logic low state, it clears the SPI shift register and switches all outputs OFF. An internal pull-up structure is provided on chip. In case the RESET Pin is pulled down statically, the device remains in Stand-by Mode Electrical Characteristics: Power Supply = -40 ° ...
Page 13
... Power Transistor Protection Functions Each of the 16 output stages has its own zener clamp, which causes a voltage limitation at the power transistor when solenoid loads are switched off. The outputs are provided with a current limitation set to a minimum for channels and 3 A for channels 9 to 16. ...
Page 14
... Typical ON Resistance versus Junction-Temperature (Channel 10, 11, 14, 15) Data Sheet Electrical and Functional Description of Blocks t ON Typical Drain-Source ON- Resistance - [°C] Typical Drain-Source ON- Resistance -50 - [°C] 14 Smart 16-Channel Low-Side Switch t t OFF t Channel 100 125 150 175 Channel 10,11,14,15 100 125 150 175 Rev.3.3, 2010-02-15 TLE6240GP ...
Page 15
... Typical Clamping Voltage versus Junction Temperature (Channel 1-8) Data Sheet Electrical and Functional Description of Blocks Typical Drain-Source ON- Resistance -50 - [°C] Typical Clamping Voltage - [°C] 15 TLE6240GP Smart 16-Channel Low-Side Switch Channel 9,12,13,16 100 125 150 175 Channel 1-8 100 125 150 175 Rev.3.3, 2010-02-15 ...
Page 16
... Figure 11 Typical Clamping Voltage versus Junction Temperature (Channel 9-16) Data Sheet Electrical and Functional Description of Blocks Typical Clamping Voltage - 100 Tj [°C] 16 TLE6240GP Smart 16-Channel Low-Side Switch Channel 9-16 125 150 175 Rev.3.3, 2010-02-15 ...
Page 17
... Short to Ground Detection Current 5.4.6 Overload Detection Threshold 5.4.7 Overtemperature Shutdown 1) Threshold 5.4.8 Overtemperature Hysteresis 5.4.9 FAULT Output Low Voltage 1) Specified by design and not subject to production test. Data Sheet Smart 16-Channel Low-Side Switch Electrical and Functional Description of Blocks Symbol Limit Values Min. Typ 2 DS(OL) S ...
Page 18
... SCKH t 50 SCKL t 200 lead t 200 lag – DIS t 200 dt t – valid – – = 200 µs. 18 TLE6240GP Smart 16-Channel Low-Side Switch Unit Conditions Typ. Max. µ – µ – I – SOH I – 0 2.5 mA SOL µ ≤ – 5 MHz – ...
Page 19
... SCLK while the serial output (SO) shifts Data Sheet Electrical and Functional Description of Blocks t SCKL t H 0.7V S 0. Smart 16-Channel Low-Side Switch 0.7VS lag 0.7VS 0. 0 Dis SO Rev.3.3, 2010-02-15 TLE6240GP ...
Page 20
... SO - Serial Output. Diagnostic data bits are shifted out serially at this pin, the most significant bit first high impedance state until the CS pin goes to a logic low state. New diagnostic data will appear at the SO pin following the rising edge of SCLK. Data Sheet Smart 16-Channel Low-Side Switch Electrical and Functional Description of Blocks 20 TLE6240GP Chapter 6 ...
Page 21
... The parallel inputs are high or low active depending on the PRG pin. If the parallel input pins are not connected (independent of high or low activity guaranteed that the outputs and are switched off. The PRG pin itself is internally pulled up when it is not connected. ...
Page 22
... Channels 9 to 16. Data Byte 2 gives the input information (on or off) for Channel 9 to 16. SO diagnosis: 16 bit diagnosis information (two bit per channel) of channels TLE6240GP Smart 16-Channel Low-Side Switch Control of the Device Control Byte1 Data Byte1 DIAG_1 (Ch Control Byte2 Data Byte2 DIAG_2 (Ch ...
Page 23
... Data Byte: ‘X’ means ‘don’t care’, because this data bits will be ignored. ‘D’ represents the data bits, either being OFF). Control words beside No Not specified Control words are not executed (cause no function) and the shift register (SO Data) is reset after the CS signal (all ‘0’). Data Sheet Smart 16-Channel Low-Side Switch ...
Page 24
... Figure 21. The data bits are ignored, so that the state of the outputs are not influenced. This command is only active once unless the next control command is again “Diagnosis only”. Diagnostic information can be read out at any time with no change of the switching conditions ...
Page 25
... SI command: No change of the output states; reading back of the 8 inputs and 1bit diagnosis for channels diagnosis: No fault, normal function of channels depending on previous SI command Figure 17 Example for two Consecutive Chip Select Cycles Data Sheet Smart 16-Channel Low-Side Switch Comment Reading back of the eight inputs and ‘1-bit Diagnosis’ provided ...
Page 26
... With LLHH LLLL as the control word, each of the input signals IN1 to IN4 are ‘OR’ed with the corresponding SI data bits. With LLHH HHHH as the control word, each of the input signals IN9 to IN12 are ‘OR’ed with the corresponding SI data bits. Data Sheet Smart 16-Channel Low-Side Switch Comment Echo-function of SPI X X ...
Page 27
... Figure 19 OR Operation between IN and Serial Input This OR operation enables the serial interface to switch the channel ON, even though the corresponding parallel input might be in the off state. SPI Priority for ON-State Also parallel control of the outputs is possible without an SPI input. The OR-function is the default Boolean operation if the device restarts after a Reset, or when the supply voltage is switched on for the first time ...
Page 28
... The AND operation implies that the output can be switched off by the SPI data bit input, even if the corresponding parallel input is in the ON state. SPI Priority for OFF-State This also implies that the serial input data bit can only switch the output channel ON if the corresponding parallel input is in the ON state ...
Page 29
... SI information: AND-operation valid for channels SO: 16 bit diagnosis for channels performed during next chip select cycle Table 13 AND-operation valid channels MSB Control Byte SI information: AND-operation valid for channels SO: 16 bit diagnosis for channels performed during next chip select cycle Data Sheet Smart 16-Channel Low-Side Switch ...
Page 30
... SI information: No change of the output states. Read back of parallel inputs and 1 bit diagnosis for channels SO: State of eight inputs plus 1 bit diagnosis for channel during next chip select cycle Diagnosis Read-Out Option 4): SPI Echo function Table 18 No change of output states - Echo MSB Control Byte Data Sheet Smart 16-Channel Low-Side Switch ...
Page 31
... SI information: Echo function of SPI interface. No change of the output states SO: During next chip select cycle the SI bits clocked in appear directly at SO because of an internal connection for this cycle CS SCLK MSB Figure 22 Serial Interface Data Sheet Byte TLE6240GP Smart 16-Channel Low-Side Switch Control of the Device Data Byte Rev.3.3, 2010-02-15 LSB LSB 0 ...
Page 32
... I/O I/O I/O I/O I/O I/O I/O I/O I/O I CLK Micro Controller * Ceramic Capacitor located close to Power Device Figure 23 Application Circuit Data Sheet Smart 16-Channel Low-Side Switch 10K 47nF* PRG FAULT RESET I/O I/O I/O I/O I/O I/O I/O I CLK TLE6240GP 32 ...
Page 33
... Engine Management Application TLE6240GP can be used in combination with Multichannel Switches for relays and general purpose loads. This arrangement covers the numerous loads to be driven in a modern Engine Management/Powertrain system. From 28 channels in sum 16 can be controlled direct in parallel for PWM applications. Figure 24 ...
Page 34
... Daisy Chain Application µC MTSR SI MRST Figure 25 Daisy Chain Application Data Sheet CLK TL6240GP TL6240GP 16-folds 16-folds 34 TLE6240GP Smart 16-Channel Low-Side Switch Application Hints CLK CLK TL6240GP 16-folds Rev.3.3, 2010-02-15 SO ...
Page 35
... Infineon Internet Page “Products”: http://www.infineon.com/products. Data Sheet 15.74 ±0.1 (Heatslug) 0.65 0.1 C 36x +0.13 0. Bottom View 15.9 ±0.1 A (Mold) 35 TLE6240GP Smart 16-Channel Low-Side Switch Package Outlines ±0. 2.8 6.3 Heatslug (Mold) 0.95 ±0.15 14.2 ±0.3 0. Heatslug 1 13.7 -0.2 (Metal) Dimensions in mm Rev.3.3, 2010-02-15 GPS09181 ...
Page 36
... Revision History Version Date Changes V3.3, 2010-02-15, up-date V3.3 2010-02-15 Template up-date ESD standard up-date Thermal Resistance parameters up-date Temperature range for functional range added Package name modified Data Sheet Smart 16-Channel Low-Side Switch 36 TLE6240GP Revision History Rev.3.3, 2010-02-15 ...
Page 37
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...