AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 222

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

22.3.1
222
AT90PWM1
Latching of Fuses
Table 77. Fuse High Byte
Notes:
Table 78. Fuse Low Byte
Note:
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if
Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
High Fuse Byte
RSTDISBL
DWEN
SPIEN
WDTON
EESAVE
BODLEVEL2
BODLEVEL1
BODLEVEL0
Low Fuse Byte
CKDIV8
CKOUT
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
(2)
1. See
2. The SPIEN Fuse is not accessible in serial programming mode.
3. See
4. See
1. The default value of SUT1..0 results in maximum start-up time for the default clock source.
2. The default setting of CKSEL3..0 results in internal RC Oscillator @ 8 MHz. See
3. The CKOUT Fuse allows the system clock to be output on PORTB0. See
4. See
(3)
(4)
(3)
(1)
See
page 34
Buffer” on page 35
(4)
(4)
(4)
“Alternate Port Functions” on page 63
“Watchdog Timer Configuration” on page 51
Table 9-2 on page 45
Table 7-10 on page 34
“System Clock Prescaler” on page 35
for details.
Bit No
Bit No
for details.
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
for BODLEVEL Fuse decoding.
for details.
Description
External Reset Disable
debugWIRE Enable
Enable Serial Program and
Data Downloading
Watchdog Timer Always On
EEPROM memory is
preserved through the Chip
Erase
Brown-out Detector trigger
level
Brown-out Detector trigger
level
Brown-out Detector trigger
level
Description
Divide clock by 8
Clock output
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
for details.
for description of RSTDISBL Fuse.
for details.
Default Value
1 (unprogrammed)
1 (unprogrammed)
0 (programmed, SPI
programming enabled)
1 (unprogrammed)
1 (unprogrammed), EEPROM
not reserved
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
Default Value
0 (programmed)
1 (unprogrammed)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
0 (programmed)
4378C–AVR–09/08
(1)
(2)
(2)
(2)
“Clock Output
Table 7-10 on
(1)
(2)