SAM9261 Atmel Corporation, SAM9261 Datasheet - Page 11

• Manufacturer Part Number: SAM9261
• Manufacturer: Atmel Corporation

Specifications of SAM9261

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 160
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

5. Power Considerations
5.1
5.2
6. I/O Line Considerations
6.1
6062LS–ATARM–23-Mar-09
Power Supplies
Power Consumption
JTAG Port Pins
The AT91SAM9261 has six types of power supply pins:
The double power supplies VDDIOM and VDDIOP are identified in
supplies enable the user to power the device differently for interfacing with memories and for
interfacing with peripherals.
Ground pins GND are common to VDDCORE, VDDIOM and VDDIOP pins power supplies. Sep-
arated ground pins are provided for VDDBU, VDDOSC and VDDPLL. The ground pins are
GNDBU, GNDOSC and GNDPLL, respectively.
The AT91SAM9261 consumes about 550 µA of static current on VDDCORE at 25°C. This static
current rises at up to 5.5 mA if the temperature increases to 85°C.
On VDDBU, the current does not exceed 3 µA @25°C, but can rise at up to 20 µA @85°C.
For dynamic power consumption, the AT91SAM9261 consumes a maximum of 50 mA on
VDDCORE at maximum speed in typical conditions (1.2V, 25°C), processor running full-perfor-
mance algorithm.
TMS, TDI and TCK are Schmitt trigger inputs and have no pull-up resistors.
TDO and RTCK are outputs, driven at up to VDDIOP, and have no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level (tied
to VDDBU). It integrates a permanent pull-down resistor of about 15 kΩ to GNDBU, so that it can
be left unconnected for normal operations.
The NTRST pin is used to initialize the embedded ICE TAP Controller when asserted at a low
level. It integrates a permanent pull-up resistor of about 15 kΩ to VDDIOP, so that it can be left
unconnected for normal operations.
• VDDCORE pins: Power the core, including the processor, the memories and the peripherals;
• VDDIOM pins: Power the External Bus Interface I/O lines; voltage ranges from 1.65V to
• VDDIOP pins: Power the Peripheral I/O lines and the USB transceivers; voltage ranges from
• VDDBU pin: Powers the Slow Clock oscillator and a part of the System Controller; voltage
• VDDPLL pin: Powers the PLL cells; voltage ranges from 3.0V and 3.6V, 3.3V nominal.
• VDDOSC pin: Powers the Main Oscillator cells; voltage ranges from 3.0V and 3.6V, 3.3V
voltage ranges from 1.08V and 1.32V, 1.2V nominal.
1.95V and 3.0V to 3.6V, 1.8V and 3.3V nominal.
2.7V and 3.6V, 3.3V nominal.
ranges from 1.08V and 1.32V, 1.2V nominal.
nominal.
Table 4-1 on page
AT91SAM9261
10. These
11