isl22416 Intersil Corporation, isl22416 Datasheet - Page 3

• Manufacturer Part Number: isl22416
• Description: Low Noise, Low Power, Spi? Bus, 128 Taps
• Manufacturer: Intersil Corporation

Analog Specifications
Absolute Maximum Ratings
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage at any Digital Interface Pin
V
Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to V
Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . . 300°C
I
Latchup (Note 4) . . . . . . . . . . . . . . . . . . Class II, Level B @+125°C
ESD (HBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5kV
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
W
VOLTAGE DIVIDER MODE (0V @ R
(Note 11, 19)
RESISTOR MODE (Measurements between R
3. θ
4. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using
CC
C
with Respect to GND . . . . . . . . . . . . . . . . . . . . . -0.3V to V
SYMBOL
V
(Note 19)
(Note 10)
(Note 15)
(Note 14)
(10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
R
I
(Note 9)
(Note 7)
(Note 8)
ZSerror
FSerror
H
LkgDCP
RH
RDNL
a max negative pulse of -1V for all pins.
RINL
TOTAL
/C
DNL
TC
(CDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V
R
INL
JA
, V
W
L
V
/C
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
RL
W
R
R
End-to-End Temperature Coefficient
Wiper Resistance
V
Potentiometer Capacitance
Leakage on DCP Pins
Integral Non-linearity
Differential Non-linearity
Zero-scale Error
Full-scale Error
Ratiometric Temperature Coefficient
Integral Non-linearity
Differential Non-linearity
H
H
RH
to R
to R
and V
L
L
Resistance
Resistance Tolerance
RL
PARAMETER
Terminal Voltages
Over recommended operating conditions unless otherwise stated.
3
L
; V
CC
@ R
W
H
and R
; measured at R
W option
U option
W option
U option
V
V
V
Voltage at pin from GND to V
Monotonic over all tap positions
W option
U option
W option
U option
DCP register set to 40 hex for W and U
option
DCP register set between 10 hex and 70 hex;
monotonic over all tap positions;
W and U option
W option
U option
L
CC
CC
RH
with R
/R
= 3.3V @ 25°C, wiper current =
and V
CC
TOTAL
+0.3
H
CC
ISL22416
not connected, or between R
RL
TEST CONDITIONS
W
, unloaded)
to GND
Thermal Information
Thermal Resistance (Typical, Note 3)
Recommended Operating Conditions
Temperature Range (Extended Industrial). . . . . . . .-40°C to +125°C
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA
CC
10 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
CC
W
and R
H
MIN
-0.5
-0.5
-20
-1
-5
-2
with R
-1
-1
0
0
0
L
(NOTE 5)
not connected)
10/10/25
TYP
±50
±80
0.1
0.5
10
50
70
±4
-1
-1
1
MAX
V
+20
200
0.5
0.5
CC
1
1
5
2
0
0
1
1
θ
June 23, 2006
JA
(Note 12)
(Note 12)
(Note 12)
(Note 19)
(Note 19)
(Note 6)
(Note 6)
(Note 6)
(Note 6)
ppm/°C
ppm/°C
ppm/°C
UNIT
120
FN6227.0
LSB
LSB
LSB
LSB
(°C/W)
kΩ
kΩ
pF
µA
MI
MI
MI
%
Ω
V