MAX5060ETI+T Maxim Integrated Products, MAX5060ETI+T Datasheet - Page 10

• Manufacturer Part Number: MAX5060ETI+T
• Description: IC CNTRLR DC-DC 28-TQFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX5060ETI+T

• Pwm Type: Current Mode
• Number Of Outputs: 1
• Frequency - Max: 1.5MHz
• Duty Cycle: 90%
• Voltage - Supply: 4.75 V ~ 28 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-TQFN Exposed Pad
• Frequency-max: 1.5MHz
• Output Voltage: 0.6 V to 5.5 V
• Output Current: 30 A
• Input Voltage: 4.75 V to 5.5 V, 7 V to 28 V
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

0.6V to 5.5V Output, Parallelable,
Average-Current-Mode DC-DC Controllers
10
MAX5060
8, 22, 25
______________________________________________________________________________________
2, 7
10
11
12
13
14
15
16
1
3
4
5
6
9
PIN
MAX5061
16
10
11
—
—
—
—
—
—
3
8
4
5
6
7
RT/SYNC
CLKOUT
PGOOD
V_IOUT
NAME
PGND
SGND
N.C.
CLP
BST
LIM
OVI
DH
DL
EN
LX
Power Ground. Connect PGND, low-side synchronous MOSFET’s source, and
V
No Connection. Not internally connected.
Low-Side Gate-Driver Output. Synchronous MOSFET gate driver.
Boost Flying-Capacitor Connection. Reservoir capacitor connection for the high-
side MOSFET driver supply. Connect a 0.47µF ceramic capacitor between BST
and LX.
Inductor Connection. Source connection for the high-side MOSFETs. Also serves
as the return terminal for the high-side driver.
High-Side Gate-Driver Output. Drives the gate of the high-side MOSFET.
Signal Ground. Ground connection for the internal control circuitry. Connect
SGND and PGND together at one point near the input bypass capacitor return.
Oscillator Output. Rising edge of CLKOUT is phase-shifted from rising edge of
DH by 180°.
Power-Good Output. PGOOD is an open-drain output that goes low when the
programmed output voltage falls out of regulation. The power-good comparator
threshold is 90% of the programmed output voltage.
Output Enable. Drive EN high or leave unconnected for normal operation. Drive
EN low to shut down the power drivers. EN has an internal 15µA pullup current.
Connect a capacitor from EN to SGND to program the hiccup mode duty cycle.
Switching Frequency Programming and Chip-Enable Input. Connect a resistor
from RT/SYNC to SGND to set the internal oscillator frequency. Drive RT/SYNC
externally to synchronize the switching frequency with system clock.
Voltage-Source Output Proportional to the Output Load Current. The voltage at
V_IOUT is 135 x I
Current-Limit Setting Input. Connect a resistor from LIM to SGND to set the
hiccup current-limit threshold. Connect a capacitor from LIM to SGND to ignore
short output overcurrent pulses.
Overvoltage Protection Circuit Input. Connect OVI to DIFF. When OVI exceeds
+12.7% above the programmed output voltage, DH is latched low and DL is
latched high. Toggle EN low to high or recycle the power to reset the latch.
Current-Error-Amplifier Output. Compensate the current loop by connecting an
RC network to ground.
DD
(MAX5060)/V
LOAD
CC
(MAX5061) bypass capacitor returns together.
x R
S
.
FUNCTION
Pin Description