PIC16F616-I/P Microchip Technology, PIC16F616-I/P Datasheet - Page 33

• Manufacturer Part Number: PIC16F616-I/P
• Description: IC PIC MCU FLASH 2KX14 14DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F616-I/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Number Of I /o: 11
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 12
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Package: 14PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 11
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP1631RD-DCPC1 - REF DES BATT CHARG OR LED DRIVERAC162083 - HEADER MPLAB ICD2 PIC16F616 8/14AC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

4.0
There are as many as eleven general purpose I/O pins
and an input pin available. Depending on which
peripherals are enabled, some or all of the pins may not
be available as general purpose I/O. In general, when a
peripheral is enabled, the associated pin may not be
used as a general purpose I/O pin.
4.1
PORTA is a 6-bit wide, bidirectional port. The
corresponding
(Register 4-2). Setting a TRISA bit (= 1) will make the
corresponding PORTA pin an input (i.e., disable the
output driver). Clearing a TRISA bit (= 0) will make the
corresponding PORTA pin an output (i.e., enables output
driver and puts the contents of the output latch on the
selected pin). The exception is RA3, which is input only
and its TRIS bit will always read as ‘1’. Example 4-1
shows how to initialize PORTA.
Reading the PORTA register (Register 4-1) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
REGISTER 4-1:
REGISTER 4-2:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-0
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-0
Note 1:
U-0
U-0
—
—
2:
I/O PORTS
PORTA and the TRISA Registers
TRISA<3> always reads ‘1’.
TRISA<5:4> always reads ‘1’ in XT, HS and LP Oscillator modes.
data
Unimplemented: Read as ‘0’
RA<5:0>: PORTA I/O Pin bit
1 = PORTA pin is > V
0 = PORTA pin is < V
Unimplemented: Read as ‘0’
TRISA<5:0>: PORTA Tri-State Control bit
1 = PORTA pin configured as an input (tri-stated)
0 = PORTA pin configured as an output
U-0
U-0
—
—
PORTA: PORTA REGISTER
TRISA: PORTA TRI-STATE REGISTER
direction
W = Writable bit
‘1’ = Bit is set
W = Writable bit
‘1’ = Bit is set
register
TRISA5
R/W-x
R/W-1
IH
IL
RA5
PIC16F610/616/16HV610/616
is
TRISA
TRISA4
R/W-0
R/W-1
RA4
Preliminary
U = Unimplemented bit, read as ‘0’
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
‘0’ = Bit is cleared
TRISA3
port pins are read, this value is modified and then
written to the PORT data latch. RA3 reads ‘0’ when
MCLRE = 1.
The TRISA register controls the direction of the
PORTA pins, even when they are being used as analog
inputs. The user must ensure the bits in the TRISA
register are maintained set when using them as analog
inputs. I/O pins configured as analog input always read
‘0’.
EXAMPLE 4-1:
RA3
R-x
R-1
BCF
CLRF
BSF
CLRF
MOVLW 0Ch
MOVWF TRISA
BCF
Note:
STATUS,RP0
PORTA
STATUS,RP0
ANSEL
STATUS,RP0
The ANSEL register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’ and cannot generate an interrupt.
TRISA2
R/W-0
R/W-1
RA2
INITIALIZING PORTA
x = Bit is unknown
x = Bit is unknown
;Bank 0
;Init PORTA
;Bank 1
;digital I/O
;Set RA<3:2> as inputs
;and set RA<5:4,1:0>
;as outputs
;Bank 0
TRISA1
R/W-0
R/W-1
RA1
DS41288C-page 31
TRISA0
R/W-0
R/W-1
RA0
bit 0
bit 0