AT89LP4052-20SU Atmel, AT89LP4052-20SU Datasheet - Page 21

• Manufacturer Part Number: AT89LP4052-20SU
• Description: IC 8051 MCU FLASH 4K 20SOIC
• Manufacturer: Atmel
• Series: 89LPr

Specifications of AT89LP4052-20SU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI/UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Package: 20SOIC W
• Device Core: 8051
• Family Name: AT89
• Maximum Speed: 20 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.2
3547J–MICRO–10/09
Input-only Mode
A second pull-up, called the “weak” pull-up, is turned on when the port register for the pin con-
tains a logic “1” and the pin itself is also at a logic “1” level. This pull-up provides the primary
source current for a quasi-bidirectional pin that is outputting a 1. If this pin is pulled low by an
external device, this weak pull-up turns off, and only the very weak pull-up remains on. In order
to pull the pin low under these conditions, the external device has to sink enough current to over-
power the weak pull-up and pull the port pin below its input threshold voltage.
The third pull-up is referred to as the “strong” pull-up. This pull-up is used to speed up low-to-
high transitions on a quasi-bidirectional port pin when the port register changes from a logic “0”
to a logic “1”. When this occurs, the strong pull-up turns on for one CPU clock, quickly pulling the
port pin high.
When in quasi-bidirectional mode the port pin will always output a “0” when corresponding bit in
the port register is also “0”. When the port register is “1” the pin may be used either as an input
or an output of “1”. The quasi-bidirectional port configuration is shown in
circuitry of P3.2 and P3.3 is not disabled during Power-down (see
Figure 15-1. Quasi-bidirectional Output
The input port configuration is shown in
input noise rejection.
Figure 15-2. Input Only
Figure 15-3. Input Only for P3.2 and P3.3
Register
From Port
Input
Input
Data
Data
PWD
1 Clock Delay
(D Flip-Flop)
Figure
Input
Data
15-2. It is a Schmitt-triggered input for improved
PWD
V
Strong
CC
AT89LP2052/LP4052
V
Weak
Very
CC
Figure
Port
Port
Pin
Pin
V
Weak
CC
15-3).
Figure
Port
Pin
15-1. The input
21