AT90USB82-16MU Atmel, AT90USB82-16MU Datasheet - Page 251

• Manufacturer Part Number: AT90USB82-16MU
• Description: IC AVR MCU 8K FLASH 32QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB82-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-QFN
• Controller Family/series: AVR USB
• No. Of I/o's: 22
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART, debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• Package: 32QFN EP
• Device Core: AVR
• Family Name: AT90
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

7707F–AVR–11/10
J. Repeat B through I until the entire Flash is programmed or until all data has been
programmed.
K. End Page Programming
Figure 25-2. Addressing the Flash Which is Organized in Pages
Note:
Figure 25-3. Programming the Flash Waveforms
Note:
3. Wait until RDY/BSY goes high (See
1. 1. Set XA1, XA0 to “10”. This enables command loading.
2. Set DATA to “0000 0000”. This is the command for No Operation.
3. Give XTAL1 a positive pulse. This loads the command, and the internal write signals
RESET +12V
are reset.
RDY/BSY
PAGEL
XTAL1
1. PCPAGE and PCWORD are listed in
DATA
1. “XX” is don’t care. The letters refer to the programming description above.
XA1
XA0
BS1
BS2
WR
OE
PROGRAM MEMORY
0x10
PROGRAM
COUNTER
A
PAGE
ADDR. LOW
PAGE ADDRESS
WITHIN THE FLASH
B
PCMSB
DATA LOW
C
PCPAGE
DATA HIGH
D
XX
E
ADDR. LOW
Figure 25-3
B
PAGEMSB
PCWORD
Table 25-11 on page
DATA LOW
C
WORD ADDRESS
WITHIN A PAGE
(1)
F
DATA HIGH
D
for signal waveforms).
INSTRUCTION WORD
XX
E
PAGE
ADDR. HIGH
G
248.
AT90USB82/162
(1)
ADDR. EXT.H
H
I
XX
PCWORD[PAGEMSB:0]:
00
01
02
PAGEEND
251