PIC18F1220-I/P Microchip Technology, PIC18F1220-I/P Datasheet - Page 19

• Manufacturer Part Number: PIC18F1220-I/P
• Description: IC MCU FLASH 2KX16 A/D 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1220-I/P

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Package: 18PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP180 - DEVICE ADAPTER 18F1320 PDIP 18LDACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.4
The ID locations are programmed much like the code
memory. The ID registers are mapped in addresses
200000h through 200007h. These locations read out
normally even after code protection.
TABLE 3-8:
© 2009 Microchip Technology Inc.
Step 1: Direct access to code memory and enable writes.
Step 2: Load write buffer with 8 bytes and write.
Note:
Command
0000
0000
0000
0000
0000
0000
0000
0000
1101
1101
1101
1111
0000
4-Bit
ID Location Programming
The user only needs to fill the first 8 bytes
of the write buffer in order to write the ID
locations.
8E A6
9C A6
0E 20
6E F8
0E 00
6E F7
0E 00
6E F6
<MSB><LSB>
<MSB><LSB>
<MSB><LSB>
<MSB><LSB>
00 00
WRITE ID SEQUENCE
Data Payload
BSF
BCF
MOVLW 20h
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 00h
MOVWF TBLPTRL
Write 2 bytes and post-increment address by 2.
Write 2 bytes and post-increment address by 2.
Write 2 bytes and post-increment address by 2.
Write 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
EECON1, EEPGD
EECON1, CFGS
Table 3-8 demonstrates the code sequence required to
write the ID locations.
In order to modify the ID locations, refer to the
methodology described in Section 3.2.1 “Modifying
Code Memory”. As with code memory, the ID
locations must be erased before being modified.
Core Instruction
PIC18F1230/1330
DS39752B-page 19