PIC24HJ12GP201-I/P Microchip Technology, PIC24HJ12GP201-I/P Datasheet - Page 39

• Manufacturer Part Number: PIC24HJ12GP201-I/P
• Description: IC PIC MCU FLASH 4KX24 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ12GP201-I/P

• Program Memory Type: FLASH
• Program Memory Size: 12KB (4K x 24)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit or 6-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164337 - MODULE SOCKET FOR PM3 40DIP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.0
The PIC24HJ12GP201/202 devices contain internal
Flash program memory for storing and executing
application code. The memory is readable, writable and
erasable during normal operation over the entire V
range.
Flash memory can be programmed in two ways:
• In-Circuit Serial Programming™ (ICSP™)
• Run-Time Self-Programming (RTSP)
ICSP allows a PIC24HJ12GP201/202 device to be
serially programmed while in the end application circuit.
This is done with two lines for programming clock and
programming data (one of the alternate programming
pin pairs: PGC1/PGD1, PGC2/PGD2 or PGC3/PGD3),
and three other lines for power (V
Master Clear (MCLR). This allows customers to
manufacture boards with unprogrammed devices and
FIGURE 4-1:
© 2007 Microchip Technology Inc.
Note:
programming capability
FLASH PROGRAM MEMORY
This data sheet summarizes the features
of the PIC24HJ12GP201/202 devices. It is
not intended to be a comprehensive
reference source. To complement the
information in this data sheet, refer to the
“PIC24H
Please see the Microchip web site
(www.microchip.com)
PIC24H
chapters.
Using
Program Counter
Using
Table Instruction
User/Configuration
Space Select
ADDRESSING FOR TABLE REGISTERS
Family
Family
Reference
Reference
DD
), ground (V
for
1/0
0
the
TBLPAG Reg
Manual”.
8 bits
Manual
SS
latest
) and
Preliminary
DD
Program Counter
24-bit EA
24 bits
PIC24HJ12GP201/202
then program the digital signal controller just before
shipping the product. This also allows the most recent
firmware or a custom firmware to be programmed.
RTSP is accomplished using TBLRD (table read) and
TBLWT (table write) instructions. With RTSP, the user
application can write program memory data either in
blocks or ‘rows’ of 64 instructions (192 bytes) at a time
or a single program memory word, and erase program
memory in blocks or ‘pages’ of 512 instructions (1536
bytes) at a time.
4.1
Regardless of the method used, all programming of
Flash memory is done with the table read and table
write instructions. These allow direct read and write
access to the program memory space from the data
memory while the device is in normal operating mode.
The 24-bit target address in the program memory is
formed using bits <7:0> of the TBLPAG register and the
Effective Address (EA) from a W register specified in
the table instruction, as shown in Figure 4-1.
The TBLRDL and the TBLWTL instructions are used to
read or write to bits<15:0> of program memory.
TBLRDL and TBLWTL can access program memory in
both Word and Byte modes.
The TBLRDH and TBLWTH instructions are used to read
or write to bits<23:16> of program memory. TBLRDH
and TBLWTH can also access program memory in Word
or Byte mode.
Working Reg EA
16 bits
Table Instructions and Flash
Programming
0
Byte
Select
DS70282B-page 37