PIC24FJ64GA102-I/SO Microchip Technology, PIC24FJ64GA102-I/SO Datasheet - Page 237

• Manufacturer Part Number: PIC24FJ64GA102-I/SO
• Description: IC MCU 16BIT 64KB FLASH 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ64GA102-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/IrDA/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM240001, MA240020, DM240002, DM240011, DV164033
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Controller Family/series: PIC24
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: I2C, LIN, SPI, USART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 24-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6-5
bit 4
Note 1:
EDG2POL
CTMUEN
R/W-0
R/W-0
If TGEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. For more
information, see Section 10.4 “Peripheral Pin Select (PPS)”.
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
Unimplemented: Read as ‘0’
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
CTTRIG: Trigger Control bit
1 = Trigger output is enabled
0 = Trigger output is disabled
EDG2POL: Edge 2 Polarity Select bit
1 = Edge 2 is programmed for a positive edge response
0 = Edge 2 is programmed for a negative edge response
EDG2SEL<1:0>: Edge 2 Source Select bits
11 = CTED1 pin
10 = CTED2 pin
01 = OC1 module
00 = Timer1 module
EDG1POL: Edge 1 Polarity Select bit
1 = Edge 1 is programmed for a positive edge response
0 = Edge 1 is programmed for a negative edge response
EDG2SEL1
R/W-0
U-0
—
CTMUCON: CTMU CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
CTMUSIDL
EDG2SEL0
R/W-0
R/W-0
EDG1POL
TGEN
R/W-0
R/W-0
PIC24FJ64GA104 FAMILY
(1)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EDG1SEL1
EDGEN
R/W-0
R/W-0
EDGSEQEN
EDG1SEL0
R/W-0
R/W-0
x = Bit is unknown
EDG2STAT
IDISSEN
R/W-0
R/W-0
DS39951C-page 237
EDG1STAT
CTTRIG
R/W-0
R/W-0
bit 8
bit 0