PIC18F86J90-I/PT Microchip Technology, PIC18F86J90-I/PT Datasheet - Page 123

• Manufacturer Part Number: PIC18F86J90-I/PT
• Description: IC PIC MCU FLASH 64KB 80-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F86J90-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 67
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3923 B
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 67
• Number Of Timers: 4
• Operating Supply Voltage: 2.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.4
PORTC is an 8-bit wide, bidirectional port. The
corresponding Data Direction and Output Latch registers
are TRISC and LATC. Only PORTC pins, RC2 through
RC7, are digital only pins and can tolerate input voltages
up to 5.5V.
PORTC is multiplexed with CCP, MSSP and EUSART
peripheral functions (Table 10-7). The pins have
Schmitt Trigger input buffers. The pins for CCP, SPI
and EUSART are also configurable for open-drain out-
put whenever these functions are active. Open-drain
configuration is selected by setting the SPIOD,
CCPxOD and U1OD control bits (TRISG<7:5> and
LATG<6>, respectively).
RC1 is normally configured as the default peripheral
pin for the CCP2 module. Assignment of CCP2 is
controlled by Configuration bit, CCP2MX (default state,
CCP2MX = 1).
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an output,
while other peripherals override the TRIS bit to make a
pin an input. The user should refer to the corresponding
peripheral section for the correct TRIS bit settings.
 2010 Microchip Technology Inc.
Note:
PORTC, TRISC and
LATC Registers
These pins are configured as digital inputs
on any device Reset.
PIC18F87J90 FAMILY
The contents of the TRISC register are affected by
peripheral overrides. Reading TRISC always returns
the current contents, even though a peripheral device
may be overriding one or more of the pins.
RC<7:1> pins are multiplexed with LCD segment
drives, controlled by bits in the LCDSE1, LCDSE2,
LCDSE3 and LCDSE4 registers. I/O port functionality
is only available when the LCD segments are disabled.
EXAMPLE 10-3:
CLRF
CLRF
MOVLW
MOVWF
PORTC
LATC
0CFh
TRISC
; Initialize PORTC by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RC<3:0> as inputs
; RC<5:4> as outputs
; RC<7:6> as inputs
INITIALIZING PORTC
DS39933D-page 123