PIC18LF6310-I/PT Microchip Technology, PIC18LF6310-I/PT Datasheet - Page 197

• Manufacturer Part Number: PIC18LF6310-I/PT
• Description: IC PIC MCU FLASH 4KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6310-I/PT

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 54
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.4.7
In I
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 16-17). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to ‘0’ and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (T
Q2 and Q4 clocks. In I
reloaded automatically.
FIGURE 16-17:
TABLE 16-3:
© 2007 Microchip Technology Inc.
Note 1:
2
C Master mode, the Baud Rate Generator (BRG)
10 MHz
10 MHz
10 MHz
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
F
CY
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE W/BRG
BAUD RATE GENERATOR BLOCK DIAGRAM
SSPM3:SSPM0
2
C Master mode, the BRG is
SCL
SSPM3:SSPM0
20 MHz
20 MHz
20 MHz
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
F
CY
CY
PIC18F6310/6410/8310/8410
*2
) on the
Reload
Control
Preliminary
CLKO
Reload
Once the given operation is complete (i.e., transmis-
sion of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
Table 16-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
2
BRG Down Counter
C specification (which applies to rates greater than
SSPADD<6:0>
BRG Value
0Dh
3Fh
0Ah
0Ah
19h
20h
28h
03h
00h
F
OSC
(2 Rollovers of BRG)
/4
400 kHz
400 kHz
333 kHz
312.5 kHz
1 MHz
DS39635B-page 195
100 kHz
308 kHz
100 kHz
100 kHz
F
SCL
(1)
(1)
(1)
(1)