DSPIC30F3014-30I/P Microchip Technology, DSPIC30F3014-30I/P Datasheet - Page 86
![IC DSPIC MCU/DSP 24K 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
DSPIC30F3014-30I/P
Manufacturer Part Number
DSPIC30F3014-30I/P
Description
IC DSPIC MCU/DSP 24K 40DIP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F3014-30IPT.pdf
(228 pages)
2.DSPIC30F3014-30IPT.pdf
(16 pages)
3.DSPIC30F3014-30IPT.pdf
(6 pages)
4.DSPIC30F3014-30IPT.pdf
(14 pages)
5.DSPIC30F3014-30IPT.pdf
(20 pages)
6.DSPIC30F3014-30IP.pdf
(244 pages)
Specifications of DSPIC30F3014-30I/P
Program Memory Type
FLASH
Package / Case
40-DIP (0.600", 15.24mm)
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
30
Program Memory Size
24KB (8K x 24)
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 13x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Data Bus Width
16 bit
Processor Series
DSPIC30F
Core
dsPIC
Maximum Clock Frequency
40 MHz
Operating Supply Voltage
2.5 V to 5.5 V
Mounting Style
Through Hole
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Data Rom Size
1024 B
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM300018, DM330011
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC30F003 - MODULE SOCKET DSPIC30F 40DIPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLEACICE0206 - ADAPTER MPLABICE 40P 600 MIL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
DSPIC30F301430/P
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F3014-30I/P
Manufacturer:
Microchip
Quantity:
328
Part Number:
DSPIC30F3014-30I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
DSPIC30F3014-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F3014-30I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
dsPIC30F3014/4013
13.2
When control bits, OCM<2:0> (OCxCON<2:0>) = 001,
010 or 011, the selected output compare channel is
configured for one of three simple Output Compare
Match modes:
• Compare forces I/O pin low
• Compare forces I/O pin high
• Compare toggles I/O pin
The OCxR register is used in these modes. The OCxR
register is loaded with a value and is compared to the
selected incrementing timer count. When a compare
occurs, one of these Compare Match modes occurs. If
the counter resets to zero before reaching the value in
OCxR, the state of the OCx pin remains unchanged.
13.3
When control bits, OCM<2:0> (OCxCON<2:0>) = 100
or 101, the selected output compare channel is config-
ured for one of two Dual Output Compare modes,
which are:
• Single Output Pulse mode
• Continuous Output Pulse mode
13.3.1
For the user to configure the module for the generation
of a single output pulse, the following steps are
required (assuming timer is off):
• Determine instruction cycle time, T
• Calculate desired pulse width value based on T
• Calculate time to Start pulse from timer start value
• Write pulse-width start and stop times into OCxR
• Set Timer Period register to value equal to or
• Set OCM<2:0> = 100.
• Enable timer, TON (TxCON<15>) = 1.
To initiate another single pulse, issue another write to
set OCM<2:0> = 100.
DS70138G-page 86
of 0x0000.
and OCxRS Compare registers (x denotes
channel 1, 2, ...,N).
greater than value in OCxRS Compare register.
Simple Output Compare Match
Mode
Dual Output Compare Match Mode
SINGLE PULSE MODE
CY
.
CY
.
13.3.2
For the user to configure the module for the generation
of a continuous stream of output pulses, the following
steps are required:
• Determine instruction cycle time, T
• Calculate desired pulse value based on T
• Calculate timer to Start pulse width from timer
• Write pulse-width Start and Stop times into OCxR
• Set Timer Period register to value equal to or
• Set OCM<2:0> = 101.
• Enable timer, TON (TxCON<15>) = 1.
13.4
When control bits, OCM<2:0> (OCxCON<2:0>) = 110
or 111, the selected output compare channel is config-
ured for the PWM mode of operation. When configured
for the PWM mode of operation, OCxR is the main latch
(read-only) and OCxRS is the secondary latch. This
enables glitchless PWM transitions.
The user must perform the following steps in order to
configure the output compare module for PWM
operation:
1.
2.
3.
4.
13.4.1
When control bits, OCM<2:0> (OCxCON<2:0>) = 111,
the selected output compare channel is again config-
ured for the PWM mode of operation with the additional
feature of input Fault protection. While in this mode, if
a logic ‘0’ is detected on the OCFA/B pin, the respective
PWM output pin is placed in the high-impedance input
state. The OCFLT bit (OCxCON<4>) indicates whether
a Fault condition has occurred. This state is maintained
until both of the following events have occurred:
• The external Fault condition has been removed.
• The PWM mode has been re-enabled by writing
start value of 0x0000.
and OCxRS (x denotes channel 1, 2, ...,N)
Compare registers, respectively.
greater than value in OCxRS Compare register.
to the appropriate control bits.
Set the PWM period by writing to the appropriate
Period register.
Set the PWM duty cycle by writing to the OCxRS
register.
Configure the output compare module for PWM
operation.
Set the TMRx prescale value and enable the
timer, TON (TxCON<15>) = 1.
Simple PWM Mode
CONTINUOUS PULSE MODE
INPUT PIN FAULT PROTECTION
FOR PWM
2010 Microchip Technology Inc.
CY
.
CY
.