PIC18F4423-I/PT Microchip Technology, PIC18F4423-I/PT Datasheet - Page 8

• Manufacturer Part Number: PIC18F4423-I/PT
• Description: IC PIC MCU FLASH 8KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4423-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 12-bit
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• Rohs Compliant: Yes
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCUAC164020 - MODULE SKT PROMATEII 44TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2423/2523/4423/4523
2.6
When the LVP Configuration bit is ‘1’ (see Section 5.3
“Single-Supply
Low-Voltage ICSP mode is enabled. As shown in
Figure 2-9, Low-Voltage ICSP Program/Verify mode is
entered by holding PGC and PGD low, placing a logic
high on PGM and then raising MCLR/V
In this mode, the RB5/PGM pin is dedicated to the
programming function and ceases to be a general
purpose I/O pin. Figure 2-10 shows the exit sequence.
The sequence that enters the device into the Program/
Verify mode places all unused I/Os in the high-impedance
state.
FIGURE 2-9:
FIGURE 2-10:
DS39759A-page 8
MCLR/V
V
PGM
PGD
PGC
MCLR/V
V
PGM
PGD
PGC
DD
DD
Entering and Exiting Low-Voltage
ICSP Program/Verify Mode
PP
PP
V
/RE3
IH
/RE3
ICSP
PGD = Input
V
PGD = Input
ENTERING LOW-VOLTAGE
PROGRAM/VERIFY MODE
IH
EXITING LOW-VOLTAGE
PROGRAM/VERIFY MODE
P15
V
P16
IH
Programming”),
P12
V
P18
IH
PP
/RE3 to V
the
IH
.
command, PGC is cycled four times. The commands
2.7
The PGC pin is used as a clock input pin and the PGD pin
is used for entering command bits and data input/output
during serial operation. Commands and data are trans-
mitted on the rising edge of PGC, latched on the falling
edge of PGC and are Least Significant bit (LSb) first.
2.7.1
All instructions are 20 bits, consisting of a leading 4-bit
command followed by a 16-bit operand, which depends
on the type of command being executed. To input a
needed for programming and verification are shown in
Table 2-4.
Depending on the 4-bit command, the 16-bit operand
represents 16 bits of input data or 8 bits of input data
and 8 bits of output data.
Throughout this specification, commands and data are
presented as illustrated in Table 2-5. The 4-bit
command is shown Most Significant bit (MSb) first. The
command operand, or “Data Payload”, is shown
<MSB><LSB>. Figure 2-11 demonstrates how to
serially present a 20-bit command/operand to the
device.
2.7.2
The core instruction passes a 16-bit instruction to the
CPU core for execution. This is needed to set up
registers as appropriate for use with other commands.
TABLE 2-4:
TABLE 2-5:
Core Instruction
(Shift in16-bit instruction)
Shift out TABLAT register
Table Read
Table Read, post-increment
Table Read, post-decrement
Table Read, pre-increment
Table Write
Table Write, post-increment by 2
Table Write, start programming,
post-increment by 2
Table Write, start programming
Command
1101
4-Bit
Serial Program/Verify Operation
4-BIT COMMANDS
CORE INSTRUCTION
Description
Payload
3C 40
Data
COMMANDS FOR
PROGRAMMING
SAMPLE COMMAND
SEQUENCE
© 2005 Microchip Technology Inc.
Table Write,
post-increment by 2
Core Instruction
Command
0000
0010
1000
1001
1010
1011
1100
1101
1110
1111
4-Bit