PIC18F2525-I/SO Microchip Technology, PIC18F2525-I/SO Datasheet - Page 26

• Manufacturer Part Number: PIC18F2525-I/SO
• Description: IC MCU FLASH 24KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2525-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 48KB (24K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3986 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MILI3DB18F4620 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2525/2620/4525/4620
TABLE 2-2:
DS39626E-page 24
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
Osc Type
DD
Note 1: Higher capacitance increases the stability
HS
XT
LP
and temperature range for the application.
2: When operating below 3V V
3: Since each resonator/crystal has its own
4: Rs may be required to avoid overdriving
5: Always verify oscillator performance over
of the oscillator but also increases the
start-up time.
using certain ceramic resonators at any
voltage, it may be necessary to use the
HS mode or switch to a crystal oscillator.
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
components.
crystals with low drive level specification.
the V
expected for the application.
10 MHz
20 MHz
25 MHz
Crystal
32 kHz
1 MHz
4 MHz
4 MHz
Freq
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
DD
and temperature range that is
Typical Capacitor Values
values
30 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
C1
Tested:
of
DD
, or when
30 pF
15 pF
15 pF
15 pF
15 pF
15 pF
15 pF
external
C2
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 2-2.
FIGURE 2-2:
2.3
The EC and ECIO Oscillator modes require an external
clock source to be connected to the OSC1 pin. There is
no oscillator start-up time required after a Power-on
Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 2-3 shows the pin connections for the EC
Oscillator mode.
FIGURE 2-3:
The ECIO Oscillator mode functions like the EC mode,
except that the OSC2 pin becomes an additional
general purpose I/O pin. The I/O pin becomes bit 6 of
PORTA (RA6). Figure 2-4 shows the pin connections
for the ECIO Oscillator mode.
FIGURE 2-4:
Clock from
Ext. System
Clock from
Ext. System
Clock from
Ext. System
External Clock Input
F
RA6
Open
OSC
/4
EXTERNAL CLOCK
INPUT OPERATION
(HS OSCILLATOR
CONFIGURATION)
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
EXTERNAL CLOCK
INPUT OPERATION
(ECIO CONFIGURATION)
© 2008 Microchip Technology Inc.
OSC1/CLKI
I/O (OSC2)
OSC1/CLKI
OSC2/CLKO
OSC1
OSC2
PIC18FXXXX
PIC18FXXXX
PIC18FXXXX
(HS Mode)