PIC16F877-04/P Microchip Technology, PIC16F877-04/P Datasheet - Page 238

• Manufacturer Part Number: PIC16F877-04/P
• Description: IC MCU FLASH 8KX14 EE 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F877-04/P

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 33
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: MSSP, PSP, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022, DV164120
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
15.4.1
DS31015A-page 15-18
Slave Mode
In slave mode, the SCL and SDA pins must be configured as inputs (TRIS set). The SSP module
will override the input state with the output data when required (slave-transmitter).
When an address is matched or the data transfer after an address match is received, the hard-
ware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF reg-
ister with the received value currently in the SSPSR register.
There are certain conditions that will cause the SSP module not to give this ACK pulse. These
are if either (or both):
a)
b)
In this case, the SSPSR register value is not loaded into the SSPBUF, but the SSPIF and SSPOV
bits are set.
tus of bits BF and SSPOV. The shaded cells show the condition where user software did not prop-
erly clear the overflow condition. Flag bit BF is cleared by reading the SSPBUF register while bit
SSPOV is cleared through software.
The SCL clock input must have a minimum high and low time for proper operation. The high and
low times of the I
Device Data Sheet electrical specifications
The buffer full bit, BF (SSPSTAT<0>), was set before the message completed.
The overflow bit, SSPOV (SSPCON<6>), was set before the message completed.
Table 15-2
2
C specification as well as the requirement of the SSP module is shown in
shows what happens when a data transfer byte is received, given the sta-
parameters 100
and 101.
1997 Microchip Technology Inc.