ATMEGA32L-8AU Atmel, ATMEGA32L-8AU Datasheet - Page 110

• Manufacturer Part Number: ATMEGA32L-8AU
• Description: IC AVR MCU 32K 8MHZ 3V 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32L-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Package: 44TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 32
• Interface Type: TWI/SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 8 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 32
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin TQFP
• Programmable Memory: 32K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2.7-5.5 V
• Data Rom Size: 1024 B
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 10 mm
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Timer/Counter1
Control Register B –
TCCR1B
2503Q–AVR–02/11
• Bit 7 – ICNC1: Input Capture Noise Canceler
Setting this bit (to one) activates the Input Capture Noise Canceler. When the Noise Canceler is
activated, the input from the Input Capture Pin (ICP1) is filtered. The filter function requires four
successive equal valued samples of the ICP1 pin for changing its output. The Input Capture is
therefore delayed by four Oscillator cycles when the Noise Canceler is enabled.
• Bit 6 – ICES1: Input Capture Edge Select
This bit selects which edge on the Input Capture Pin (ICP1) that is used to trigger a capture
event. When the ICES1 bit is written to zero, a falling (negative) edge is used as trigger, and
when the ICES1 bit is written to one, a rising (positive) edge will trigger the capture.
When a capture is triggered according to the ICES1 setting, the counter value is copied into the
Input Capture Register (ICR1). The event will also set the Input Capture Flag (ICF1), and this
can be used to cause an Input Capture Interrupt, if this interrupt is enabled.
When the ICR1 is used as TOP value (see description of the WGM13:0 bits located in the
TCCR1A and the TCCR1B Register), the ICP1 is disconnected and consequently the Input Cap-
ture function is disabled.
• Bit 5 – Reserved Bit
This bit is reserved for future use. For ensuring compatibility with future devices, this bit must be
written to zero when TCCR1B is written.
• Bit 4:3 – WGM13:2: Waveform Generation Mode
See TCCR1A Register description.
• Bit 2:0 – CS12:0: Clock Select
The three Clock Select bits select the clock source to be used by the Timer/Counter, see
49
Table 48. Clock Select Bit Description
Bit
Read/Write
Initial Value
CS12
and
0
0
0
0
1
1
1
1
Figure
CS11
0
0
1
1
0
0
1
1
ICNC1
50.
R/W
7
0
CS10
ICES1
0
1
0
1
0
1
0
1
R/W
6
0
Description
No clock source (Timer/Counter stopped).
clk
clk
clk
clk
clk
External clock source on T1 pin. Clock on falling edge.
External clock source on T1 pin. Clock on rising edge.
I/O
I/O
I/O
I/O
I/O
R
5
–
0
/1 (No prescaling)
/8 (From prescaler)
/64 (From prescaler)
/256 (From prescaler)
/1024 (From prescaler)
WGM13
R/W
4
0
WGM12
R/W
3
0
CS12
R/W
2
0
CS11
R/W
1
0
ATmega32(L)
CS10
R/W
0
0
TCCR1B
Figure
110