C8051F413-GM Silicon Laboratories Inc, C8051F413-GM Datasheet - Page 127

• Manufacturer Part Number: C8051F413-GM
• Description: IC 8051 MCU 16K FLASH 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F41xr

Specifications of C8051F413-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 20
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.25 V
• Data Converters: A/D 20x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F4x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F410DK
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 2-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1454 - ADAPTER PROGRAM TOOLSTICK F411336-1317 - KIT EVAL FOR C8051F411336-1314 - KIT DEV FOR C8051F41X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1311

15. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:
•
•
•
•
All SFRs are reset to the predefined values noted in the SFR detailed descriptions. The contents of internal
data memory are unaffected during a reset; any previously stored data is preserved. However, since the
stack pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.
The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled dur-
ing and after the reset. For V
exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to the inter-
nal oscillator. Refer to
the system clock source. The Watchdog Timer is enabled with the system clock divided by 12 as its clock
source (
Program execution begins at location 0x0000.
Px.x
Px.x
CIP-51 halts program execution
Special Function Registers (SFRs) are initialized to their defined reset values
External Port pins are forced to a known state
Interrupts and timers are disabled.
smaRTClock
Section “25.3. Watchdog Timer Mode” on page 257
System
Clock
Comparator 0
RTC0RE
+
-
Section “19. Oscillators” on page 165
C0RSEF
Detector
Missing
Clock
(one-
shot)
Microcontroller
EN
Extended Interrupt
DD
CIP-51
Core
Handler
Monitor and power-on resets, the RST pin is driven low until the device
Figure 15.1. Reset Sources
WDT
PCA
EN
VDD
System Reset
Supply
Monitor
+
-
Rev. 1.1
Enable
(Software Reset)
SWRSF
for information on selecting and configuring
details the use of the Watchdog Timer).
'0'
Power On
C8051F410/1/2/3
Reset
Illegal Flash
Operation
(wired-OR)
Funnel
Reset
/RST
127