SAK-XC2267-96F66L AC Infineon Technologies, SAK-XC2267-96F66L AC Datasheet - Page 74
![IC MCU 16BIT FLASH PG-LQFP-100](/photos/12/23/122306/sak-xc2267-96f66l82_ac_sml.jpg)
SAK-XC2267-96F66L AC
Manufacturer Part Number
SAK-XC2267-96F66L AC
Description
IC MCU 16BIT FLASH PG-LQFP-100
Manufacturer
Infineon Technologies
Series
XC22xxr
Datasheet
1.SAK-XC2264-56F66L_AC.pdf
(116 pages)
Specifications of SAK-XC2267-96F66L AC
Core Processor
C166SV2
Core Size
16/32-Bit
Speed
66MHz
Connectivity
CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
Peripherals
DMA, I²S, POR, PWM, WDT
Number Of I /o
75
Program Memory Size
768KB (768K x 8)
Program Memory Type
FLASH
Ram Size
82K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 16x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
100-LFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
KX226796F66L82ACXT
SAK-XC2267-96F66L82 AC
SAK-XC2267-96F66L82ACINTR
SAK-XC2267-96F66L82ACINTR
SAK-XC2267-96F66LACINTR
SP000250942
SAK-XC2267-96F66L82 AC
SAK-XC2267-96F66L82ACINTR
SAK-XC2267-96F66L82ACINTR
SAK-XC2267-96F66LACINTR
SP000250942
4.2
These parameters are static or average values that may be exceeded during switching
transitions (e.g. output current).
The XC226x can operate within a wide supply voltage range from 3.0 V to 5.5 V.
However, during operation this supply voltage must remain within 10 percent of the
selected nominal supply voltage. It cannot vary across the full operating voltage range.
Because of the supply voltage restriction and because electrical behavior depends on
the supply voltage, the parameters are specified separately for the upper and the lower
voltage range.
During operation, the supply voltages may only change with a maximum speed of
dV/dt < 1 V/ms.
Leakage current is strongly dependent on the operating temperature and the voltage
level at the respective pin. The maximum values in the following tables apply under worst
case conditions, i.e. maximum temperature and an input level equal to the supply
voltage.
The value for the leakage current in an application can be determined by using the
respective leakage derating formula (see tables) with values from that application.
The pads of the XC226x are designed to operate in various driver modes. The DC
parameter specifications refer to the current limits in
Table 13
Port Output Driver
Mode
Strong driver
Medium driver
Weak driver
1) An output current above |
Data Sheet
For any group of 16 neighboring output pins, the total output current in each direction (Σ
remain below 50 mA.
DC Parameters
Current Limits for Port Output Drivers
I
OXnom
Maximum Output Current
(
V
10 mA
4.0 mA
0.5 mA
I
OLmax
DDP
| may be drawn from up to three pins at the same time.
≥ 4.5 V
, -
I
OHmax
)
1)
V
10 mA
2.5 mA
0.5 mA
DDP
72
< 4.5 V
Table
XC2000 Family Derivatives
Nominal Output Current
(
V
2.5 mA
1.0 mA
0.1 mA
I
DDP
OLnom
13.
≥ 4.5 V
, -
Electrical Parameters
I
OHnom
XC2267 / XC2264
)
V
2.5 mA
1.0 mA
0.1 mA
I
OL
DDP
V2.1, 2008-08
and Σ-
< 4.5 V
I
OH
) must