SAK-C161CS-LF CA Infineon Technologies, SAK-C161CS-LF CA Datasheet - Page 57
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAK-C161CS-LF CA
Manufacturer Part Number
SAK-C161CS-LF CA
Description
IC MCU 16BIT 256KB TQFP-128-2
Manufacturer
Infineon Technologies
Series
C16xxr
Datasheet
1.SAK-C161CS-LF_CA.pdf
(89 pages)
Specifications of SAK-C161CS-LF CA
Core Processor
C166
Core Size
16-Bit
Speed
25MHz
Connectivity
CAN, EBI/EMI, I²C, SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
93
Program Memory Type
ROMless
Ram Size
10K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
128-LFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Program Memory Size
-
Other names
K161CSLFCANP
K161CSLFCAXT
SAK-C161CS-LFCA
SAK-C161CS-LFCAINTR
SAK-C161CS-LFCATR
SAK-C161CS-LFCATR
SAKC161CSLFCAXT
SP000106869
K161CSLFCAXT
SAK-C161CS-LFCA
SAK-C161CS-LFCAINTR
SAK-C161CS-LFCATR
SAK-C161CS-LFCATR
SAKC161CSLFCAXT
SP000106869
6)
7)
8)
9)
10)
11)
Power Consumption C161CS/JC/JI
(Operating Conditions apply)
Parameter
Power supply current (active)
with all peripherals active
Idle mode supply current
with all peripherals active
Idle mode supply curr., Main osc,
with all peripherals deactivated,
PLL off, SDD factor = 32
Idle mode supply curr., Aux. osc,
with all peripherals deactivated,
PLL off, SDD factor = 32
Sleep and Power-down mode
supply current with RTC running
on main oscillator
Sleep and Power-down mode
supply current with RTC disabled
1)
2)
3)
Data Sheet
These parameters describe the RSTIN pullup, which equals a resistance of ca. 50 to 250 k .
The maximum current may be drawn while the respective signal line remains inactive.
The minimum current must be drawn in order to drive the respective signal line active.
This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins
are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The
READY-pullup is always active, except for Powerdown mode.
This specification is valid during Reset and during Adapt-mode.
Not 100% tested, guaranteed by design and characterization.
The supply current is a function of the operating frequency. This dependency is illustrated in
These parameters are tested at
at
This parameter is determined mainly by the current consumed by the oscillator (see
however, is influenced by the external oscillator circuitry (crystal, capacitors). The values given refer to a typical
circuitry and may change in case of a not optimized external oscillator circuitry.
This parameter is tested including leakage currents. All inputs (including pins configured as inputs) at 0 V to
0.1 V or at
V
IL
or
V
IH
V
.
DD
- 0.1 V to
V
DD
, all outputs (including pins configured as outputs) disconnected.
V
DDmax
and maximum CPU clock with all outputs disconnected and all inputs
Symbol
I
I
I
I
I
I
DD
IDX
IDOM
IDOA
PDRM
PDO
2)
2)
2)
53
min.
–
–
–
–
–
–
Limit Values
max.
15 +
2.5
5 +
1.5
500 +
50
100
200 +
25
50
f
f
f
f
OSC
OSC
CPU
CPU
Unit Test Condition
mA
mA
A
A
A
A
C161CS/JC/JI-32R
C161CS/JC/JI-L
Figure
RSTIN =
f
RSTIN =
f
RSTIN =
f
V
f
V
f
V
CPU
CPU
OSC
OSC
OSC
DD
DD
DD
Figure
V3.0, 2001-01
=
=
=
9). This current,
in [MHz]
in [MHz]
in [MHz]
= 32 kHz
in [MHz]
V
V
V
DDmax
DDmax
DDmax
V
V
V
10.
IL
IH1
IH1
1)
1)
1)
3)
3)
3)