PIC24HJ32GP202-I/MM Microchip Technology, PIC24HJ32GP202-I/MM Datasheet - Page 145
![IC PIC MCU FLASH 32K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
PIC24HJ32GP202-I/MM
Manufacturer Part Number
PIC24HJ32GP202-I/MM
Description
IC PIC MCU FLASH 32K 28QFN
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ32GP202-ISO.pdf
(272 pages)
3.PIC24HJ32GP202-ISO.pdf
(8 pages)
4.PIC24HJ32GP202-ISO.pdf
(12 pages)
5.PIC24HJ32GP204-IML.pdf
(244 pages)
Specifications of PIC24HJ32GP202-I/MM
Program Memory Type
FLASH
Program Memory Size
32KB (11K x 24)
Package / Case
28-QFN
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
2 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
21
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
Minimum Operating Temperature
- 40 C
On-chip Adc
10-ch x 12-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
15.5
The 10-bit I2CxADD register contains the Slave mode
addresses.
If the A10M bit (I2CxCON<10>) is ‘0’, the address is
interpreted by the module as a 7-bit address. When an
address is received, it is compared to the seven Least
Significant bits of the I2CxADD register.
If the A10M bit is ‘1’, the address is assumed to be a
10-bit address. When an address is received, it is com-
pared with the binary value, ‘11110 A9 A8’ (where A9
and A8 are two Most Significant bits of I2CxADD). If
that value matches, the next address will be compared
with the Least Significant 8 bits of I2CxADD, as speci-
fied in the 10-bit addressing protocol.
TABLE 15-1:
15.6
The I2CxMSK register (Register 15-3) designates
address bit positions as “don’t care” for both 7-bit and
10-bit Address modes. Setting a particular bit location
(= 1) in the I2CxMSK register causes the slave module
to respond, whether the corresponding address bit
value is a ‘0’ or ‘1’. For example, when I2CxMSK is set
to ‘00100000’, the Slave module will detect both
addresses, ‘0000000’ and ‘00100000’.
To enable address masking, the IPMI (Intelligent
Peripheral Management Interface) must be disabled by
clearing the IPMIEN bit (I2CxCON<11>).
15.7
The control bit IPMIEN enables the module to support
the Intelligent Peripheral Management Interface (IPMI).
When this bit is set, the module accepts and acts upon
all addresses.
© 2007 Microchip Technology Inc.
0x00
0x01-0x03
0x04-0x07
0x08-0x77
0x78-0x7b
0x7c-0x7f
I
Slave Address Masking
IPMI Support
2
C Module Addresses
PIC24HJ32GP202/204 and PIC24HJ16GP304
7-BIT I
ADDRESSES SUPPORTED BY
PIC24HJ32GP202/204 AND
PIC24HJ16GP304
General call address or Start byte
Reserved
Hs mode Master codes
Valid 7-bit addresses
Valid 10-bit addresses
(lower 7 bits)
Reserved
2
C™ SLAVE
Preliminary
15.8
The general call address can address all devices.
When this address is used, all devices should, in
theory, respond with an Acknowledgement.
The general call address is one of eight addresses
reserved for specific purposes by the I
consists of all ‘0’s with R_W = 0.
The general call address is recognized when the General
Call Enable (GCEN) bit is set (I2CxCON<7> = 1). When
the interrupt is serviced, the source for the interrupt can
be checked by reading the contents of the I2CxRCV to
determine if the address was device-specific or a general
call address.
15.9
In Slave modes, the module can synchronize buffer
reads and write to the master device by clock stretching.
15.9.1
Both 10-bit and 7-bit Transmit modes implement clock
stretching by asserting the SCLREL bit after the falling
edge of the ninth clock, if the TBF bit is cleared,
indicating the buffer is empty.
In Slave Transmit modes, clock stretching is always
performed, irrespective of the STREN bit. The user’s
ISR must set the SCLREL bit before transmission is
allowed to continue. By holding the SCLx line low, the
user application has time to service the ISR and load
the contents of the I2CxTRN before the master device
can initiate another transmit sequence.
15.9.2
The STREN bit in the I2CxCON register can be used to
enable clock stretching in Slave Receive mode. When
the STREN bit is set, the SCLx pin will be held low at
the end of each data receive sequence.
The user’s ISR must set the SCLREL bit before recep-
tion is allowed to continue. By holding the SCLx line
low, the user application has time to service the ISR
and read the contents of the I2CxRCV before the mas-
ter device can initiate another receive sequence. This
prevents buffer overruns.
15.10 Software Controlled Clock
When the STREN bit is ‘1’, the software can clear the
SCLREL bit to allow software to control the clock
stretching.
If the STREN bit is ‘0’, a software write to the SCLREL
bit is disregarded and has no effect on the SCLREL bit.
General Call Address Support
Automatic Clock Stretch
Stretching (STREN = 1)
TRANSMIT CLOCK STRETCHING
RECEIVE CLOCK STRETCHING
DS70289A-page 143
2
C protocol. It