T89C5115-TISUM Atmel, T89C5115-TISUM Datasheet - Page 49
T89C5115-TISUM
Manufacturer Part Number
T89C5115-TISUM
Description
IC 8051 MCU FLASH 16K 28SOIC
Manufacturer
Atmel
Series
89Cr
Datasheet
1.T89C5115-RATIM.pdf
(113 pages)
Specifications of T89C5115-TISUM
Core Processor
8051
Core Size
8-Bit
Speed
40MHz
Connectivity
UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
20
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
89C5115-TISUM
- Current page: 49 of 113
- Download datasheet (2Mb)
Serial I/O Port
Figure 20. Serial I/O Port Block Diagram
4128G–8051–02/08
Framing Error Detection
TXD
RXD
The T89C5115 I/O serial port is compatible with the I/O serial port in the 80C52.
It provides both synchronous and asynchronous communication modes. It operates as a
Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes
(Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously
and at different baud rates
Serial I/O port includes the following enhancements:
•
•
Framing bit error detection is provided for the three asynchronous modes. To enable the
framing bit error detection feature, set SMOD0 bit in PCON register.
Figure 21. Framing Error Block Diagram
When this feature is enabled, the receiver checks each incoming data frame for a valid
stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous
transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in
SCON register bit is set.
The software may examine the FE bit after each reception to check for data errors.
Once set, only software or a reset clears the FE bit. Subsequently received frames with
valid stop bits cannot clear the FE bit. When the FE feature is enabled, RI rises on the
stop bit instead of the last data bit (See Figure 22 and Figure 23).
Framing error detection
Automatic address recognition
Transmitter
SBUF
Mode 0 Transmit
IB Bus
Write SBUF
SM0/FE
SMOD1
SCON reg
RI
SMOD0
TI
SM1
SM2
-
Shift register
Receive
Receiver
SBUF
REN
Set FE bit if Stop bit is 0 (Framing Error)
SM0 to UART Mode Control
POF
To UART Framing Error Control
TB8
GF1
Read SBUF
Load SBUF
Serial Port
Interrupt
RB8
GF0
PD
TI
Request
IDL
RI
49
Related parts for T89C5115-TISUM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC 8051 MCU FLASH 16K 32VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 28PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 24SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 28SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Low Pin Count 8-bit MCU with A/D Converter and 16-Kbytes of Flash Memory
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: