ATA6613P-PLQW Atmel, ATA6613P-PLQW Datasheet - Page 285

• Manufacturer Part Number: ATA6613P-PLQW
• Description: MCU W/LIN TXRX REG WTCHDG 48-QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6613P-PLQW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: ATA6x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.23.3
6.23.3.1
6.23.3.2
9111H–AUTO–01/11
Read-While-Write and No Read-While-Write Flash Sections
RWW – Read-While-Write Section
NRWW – No Read-While-Write Section
Whether the CPU supports Read-While-Write or if the CPU is halted during a Boot Loader
software update is dependent on which address that is being programmed. In addition to the
two sections that are configurable by the BOOTSZ Fuses as described above, the Flash is
also divided into two fixed sections, the Read-While-Write (RWW) section and the No
Read-While-Write (NRWW) section. The limit between the RWW- and NRWW sections is
given in
between the two sections is:
Note that the user software can never read any code that is located inside the RWW section
during a Boot Loader software operation. The syntax “Read-While-Write section” refers to
which section that is being programmed (erased or written), not which section that actually is
being read during a Boot Loader software update.
If a Boot Loader software update is programming a page inside the RWW section, it is possi-
ble to read code from the Flash, but only code that is located in the NRWW section. During an
on-going programming, the software must ensure that the RWW section never is being read. If
the user software is trying to read code that is located inside the RWW section (i.e., by a
call/jmp/lpm or an interrupt) during programming, the software might end up in an unknown
state. To avoid this, the interrupts should either be disabled or moved to the Boot Loader sec-
tion. The Boot Loader section is always located in the NRWW section. The RWW Section
Busy bit (RWWSB) in the Store Program Memory Control and Status Register (SPMCSR) will
be read as logical one as long as the RWW section is blocked for reading. After a program-
ming is completed, the RWWSB must be cleared by software before reading code located in
the RWW section. See
page 289
The code located in the NRWW section can be read when the Boot Loader software is updat-
ing a page in the RWW section. When the Boot Loader code updates the NRWW section, the
CPU is halted during the entire Page Erase or Page Write operation.
Table 6-102. Read-While-Write Features
Address During the Programming?
• When erasing or writing a page located inside the RWW section, the NRWW section can
• When erasing or writing a page located inside the NRWW section, the CPU is halted during
Which Section does the Z-pointer
be read during the operation.
the entire operation.
Table 6-108 on page 298
for details on how to clear RWWSB.
NRWW Section
RWW Section
“Store Program Memory Control and Status Register – SPMCSR” on
Which Section Can be
and
Programming?
NRWW Section
Read During
Figure 6-115 on page
None
Atmel ATA6612/ATA6613
Is the CPU
Halted?
Yes
No
287. The main difference
Read-While-Write
Supported?
Yes
No
285