PIC18F1220-I/SS Microchip Technology, PIC18F1220-I/SS Datasheet - Page 124

• Manufacturer Part Number: PIC18F1220-I/SS
• Description: IC MCU FLASH 2KX16 A/D 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1220-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Package: 20SSOP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC164307 - MODULE SKT FOR PM3 28SSOPAC164018 - MODULE SKT PROMATEII 20SSOP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F1220/1320
15.5.4
In the Half-Bridge Output mode, two pins are used as
outputs to drive push-pull loads. The PWM output
signal is output on the RB3/CCP1/P1A pin, while the
complementary PWM output signal is output on the
RB2/P1B/INT2 pin (Figure 15-6). This mode can be
used for half-bridge applications, as shown in
Figure 15-7, or for full-bridge applications, where four
power switches are being modulated with two PWM
signals.
In Half-Bridge Output mode, the programmable dead-
band delay can be used to prevent shoot-through
current in half-bridge power devices. The value of bits,
PDC6:PDC0 (PWM1CON<6:0>), sets the number of
instruction cycles before the output is driven active. If the
value is greater than the duty cycle, the corresponding
output remains inactive during the entire cycle. See
Section 15.5.6 “Programmable Dead-Band Delay”
for more details of the dead-band delay operations.
FIGURE 15-7:
DS39605C-page 122
Standard Half-Bridge Circuit (“Push-Pull”)
Half-Bridge Output Driving a Full-Bridge Circuit
HALF-BRIDGE MODE
EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS
PIC18F1220/1320
P1A
P1B
PIC18F1220/1320
P1A
P1B
FET
Driver
FET
Driver
FET
Driver
FET
Driver
The TRISB<3> and TRISB<2> bits must be cleared to
configure P1A and P1B as outputs.
FIGURE 15-6:
P1A
P1B
Note 1: At this time, the TMR2 register is equal to the
td = Dead-Band Delay
Load
V+
V-
(1)
PR2 register.
td
Duty Cycle
Period
Load
td
HALF-BRIDGE PWM
OUTPUT (ACTIVE-HIGH)
 2004 Microchip Technology Inc.
FET
Driver
FET
Driver
(1)
+
V
-
+
V
-
Period
(1)