PIC18LF1330-I/SO Microchip Technology, PIC18LF1330-I/SO Datasheet - Page 134

• Manufacturer Part Number: PIC18LF1330-I/SO
• Description: IC PIC MCU FLASH 4KX16 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF1330-I/SO

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 40MHz
• No.: RoHS Compliant
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F1230/1330
14.6.5
The Complementary mode of PWM operation is useful
to drive one or more power switches in half-bridge
configuration, as shown in Figure 14-16. This inverter
topology is typical for a 3-phase induction motor,
brushless DC motor or 3-phase Uninterruptible Power
Supply (UPS) control applications.
Each upper/lower power switch pair is fed by a
complementary PWM signal. Dead time may be
optionally inserted during device switching, where both
outputs are inactive for a short period (see
Section 14.7 “Dead-Time Generators”).
In Complementary mode, the duty cycle comparison
units are assigned to the PWM outputs as follows:
• PDC0 register controls PWM1/PWM0 outputs
• PDC1 register controls PWM3/PWM2 outputs
• PDC2 register controls PWM5/PWM4 outputs
PWM1/3/5 are the main PWMs that are controlled by
the
complemented outputs. When using the PWMs to
control the half-bridge, the odd number PWMs can be
used to control the upper power switch and the even
numbered PWMs can be used for the lower switches.
DS39758D-page 134
PDCx
COMPLEMENTARY PWM
OPERATION
registers
and
PWM0/2/4
are
the
FIGURE 14-16:
The Complementary mode is selected for each PWM
I/O pin pair by clearing the appropriate PMODx bit in
the PWMCON0 register. The PWM I/O pins are set to
Complementary mode by default upon all kinds of
device Resets.
+V
TYPICAL LOAD FOR
COMPLEMENTARY PWM
OUTPUTS
 2009 Microchip Technology Inc.
3-Phase
Load