PIC18F4455-I/P Microchip Technology, PIC18F4455-I/P Datasheet - Page 14

• Manufacturer Part Number: PIC18F4455-I/P
• Description: IC PIC MCU FLASH 12KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4455-I/P

• Program Memory Type: FLASH
• Program Memory Size: 24KB (12K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Eeprom Size: 256 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI/I2C/EAUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163025
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4550 - BOARD DAUGHTER ICEPIC3DM163025 - PIC DEM FULL SPEED USB DEMO BRDDVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2455/2550/4455/4550
31. Module: MSSP
TABLE 3:
DS80478A-page 14
Param
70
No.
When operated in I
baud rate may be somewhat slower than predicted
by the following formula:
Work around
If the target application is sensitive to the baud rate
and requires more precision, the SSPADD value
can be adjusted to compensate.
If this work around is going to be used, it is recom-
mended that the firmware first check the Revision
ID by reading the DEVID1 value at address,
3FFFFEh. Silicon revisions, B6 and B7, will match
the I
Affected Silicon Revisions
I
A3
2
T
T
X
2
C Master mode, clock
SS
SS
Symbol
C baud rate predicted by the given formula.
L2
L2
SC
SC
EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING)
H,
L
B4
X
SS ↓ to SCK ↓ or SCK ↑ Input
2
C™ Master mode, the I
B5
X
=
--------------------------------------------- -
4
•
(
SSPADD
B6
F
OSC
Characteristic
+
B7
1
)
2
C
32. Module: MSSP
In SPI Slave mode with slave select enabled
(SSPM<3:0> = 0100), the minimum time between
the falling edge of the SS pin and first SCK edge
is greater than specified in parameter 70 in
Table 28-17 and Table 28-18. The updated
The minimum time between SS pin low and an
SSPBUF write is also 3 T
the SS pin occurs greater than 3 T
first SCK edge or loading SSPBUF, the peripheral
will function correctly. Also, if SSPBUF is written
prior to the SS pin going low, the peripheral will
function correctly.
Work around
None.
Affected Silicon Revisions
specification is shown in bold in Table 3.
A3
3 T
B4
Min
X
CY
© 2009 Microchip Technology Inc.
B5
Max Units Conditions
X
—
CY
. If the falling edge of
ns
B6
X
CY
, before the
B7
X