DSPIC30F5015-30I/PT Microchip Technology, DSPIC30F5015-30I/PT Datasheet - Page 68

• Manufacturer Part Number: DSPIC30F5015-30I/PT
• Description: IC DSPIC MCU/DSP 66K 64TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5015-30I/PT

• Program Memory Type: FLASH
• Program Memory Size: 66KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 52
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• Maximum Clock Frequency: 30 MHz
• Number Of Programmable I/os: 52
• Data Ram Size: 2 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM330011
• Minimum Operating Temperature: - 40 C
• Package: 64TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 16-chx10-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPAC30F008 - MODULE SKT FOR DSPIC30F 64TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DSPIC30F501530IPT

dsPIC30F5015/5016
FIGURE 9-1:
9.1
The 16-bit timer can be placed in the Gated Time
Accumulation mode. This mode allows the internal T
to increment the respective timer when the gate input
signal (T1CK pin) is asserted high. Control bit TGATE
(T1CON<6>) must be set to enable this mode. The
timer must be enabled (TON = 1) and the timer clock
source set to internal (TCS = 0).
When the CPU goes into the Idle mode, the timer will
stop incrementing unless TSIDL = 0. If TSIDL = 1, the
timer will resume the incrementing sequence upon
termination of the CPU Idle mode.
9.2
The input clock (F
timer has a prescale option of 1:1, 1:8, 1:64 and 1:256,
selected by control bits, TCKPS<1:0> (T1CON<5:4>).
The prescaler counter is cleared when any of the
following occurs:
• a write to the TMR1 register
• clearing of the TON bit (T1CON<15>)
• device Reset such as POR and BOR
However, if the timer is disabled (TON = 0), then the
timer prescaler cannot be reset since the prescaler
clock is halted.
TMR1 is not cleared when T1CON is written. It is
cleared by writing to the TMR1 register.
DS70149C-page 66
Timer Gate Operation
Timer Prescaler
SOSCO/
SOSCI
T1IF
Event Flag
T1CK
OSC
/4 or external clock) to the 16-bit
16-BIT TIMER1 MODULE BLOCK DIAGRAM (TYPE A TIMER)
TGATE
0
1
Reset
Equal
LPOSCEN
Comparator x 16
TMR1
PR1
CY
Q
Q
Gate
Sync
CK
T
D
CY
9.3
During CPU Sleep mode, the timer will operate if:
• The timer module is enabled (TON = 1) and
• The timer clock source is selected as external
• The TSYNC bit (T1CON<2>) is asserted to a logic
When all three conditions are true, the timer will con-
tinue to count up to the Period register and be reset to
0x0000.
When a match between the timer and the Period regis-
ter occurs, an interrupt can be generated, if the
respective timer interrupt enable bit is asserted.
TGATE
(TCS = 1) and
‘0’, which defines the external clock source as
asynchronous
Timer Operation During Sleep
Mode
1 x
0 1
0 0
TON
TSYNC
© 2007 Microchip Technology Inc.
0
1
TCKPS<1:0>
1, 8, 64, 256
Prescaler
Sync
2