STM32F102RBT6 STMicroelectronics, STM32F102RBT6 Datasheet - Page 26

• Manufacturer Part Number: STM32F102RBT6
• Description: MCU ARM 32BIT 128KB FLASH 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F102RBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8312

Electrical characteristics
26/69
Table 6.
1. All main power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum I
Table 7.
I
INJ(PIN)
I
supply, in the permitted range.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
STG
T
J
(2)(3)
must never be exceeded. This is implicitly insured if V
(2)
Current characteristics
Thermal characteristics
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on High-speed external OSC_IN and Low-
speed external OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
INJ(PIN)
IN
>V
) and ground (V
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 15056 Rev 3
DD
SS
/V
Ratings
SS
DDA
ground lines (sink)
, V
Ratings
SSA
power lines (source)
) pins must always be connected to the external power
(4)
IN
maximum is respected. If V
(1)
STM32F102x8, STM32F102xB
(1)
INJ(PIN)
IN
<V
INJ(PIN)
(4)
Section 5.3.16: 12-bit ADC
SS
–65 to +150
is the absolute sum of the
.
value. A positive
Value
150
Max.
 25
± 25
150
150
± 5
± 5
± 5
25
IN
maximum
Unit
Unit
°C
°C
mA