STM32F102RBT6 STMicroelectronics, STM32F102RBT6 Datasheet - Page 59

• Manufacturer Part Number: STM32F102RBT6
• Description: MCU ARM 32BIT 128KB FLASH 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F102RBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-8312

STM32F102x8, STM32F102xB
Note:
Table 45.
1. Data guaranteed by design, not tested in production.
Table 46.
1. ADC DC accuracy values are measured after internal calibration.
2. Based on characterization, not tested in production.
Table 47.
1. ADC DC accuracy values are measured after internal calibration.
2. Better performance could be achieved in restricted V
3. Based on characterization, not tested in production.
ADC accuracy vs. negative injection current: Injecting a negative current on any of the
standard (non-robust) analog pins should be avoided as this significantly reduces the
accuracy of the conversion being performed on another analog pin. It is recommended to
add a Schottky diode (pin to ground) to standard analog pins that may potentially inject
negative current.
Any positive injection current within the limits specified for I
Section 5.3.12
1.5
7.5
13.5
28.5
41.5
55.5
71.5
239.5
Symbol
Symbol
EO
EG
EO
EG
ED
ED
ET
EL
ET
EL
T
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
s
R
(cycles)
ADC accuracy - limited test conditions
ADC accuracy
AIN
does not affect the ADC accuracy.
Parameter
Parameter
max for f
ADC
(1) (2)
Doc ID 15056 Rev 3
0.13
0.63
1.13
2.38
3.46
4.63
5.96
19.96
= 12 MHz
f
f
V
T
Measurements made after
ADC calibration
f
f
V
Measurements made after
ADC calibration
PCLK2
ADC
PCLK2
ADC
A
DDA
DDA
= 25 °C
= 12 MHz, R
= 12 MHz, R
(1)
= 3 V to 3.6 V
= 2.4 V to 3.6 V
t
S
= 48 MHz,
= 48 MHz,
Test conditions
Test conditions
(µs)
DD
, frequency and temperature ranges.
AIN
AIN
(1)
< 10 k,
< 10 k,
INJ(PIN)
0.4
5.9
11.4
25.2
37.2
50
NA
NA
Electrical characteristics
and
±1.3
±0.5
±0.7
±0.8
±1.5
±1.5
±1.5
Typ
Typ
±1
±2
±1
R

AIN
I
INJ(PIN)
max (k)
Max
Max
±1.5
±1.5
±1.5
±2.5
±1
±3
±2
±2
±5
±3
(2)
(3)
in
Unit
LSB
Unit
LSB
59/69