MC9S08SH8CTG Freescale Semiconductor, MC9S08SH8CTG Datasheet - Page 312

• Manufacturer Part Number: MC9S08SH8CTG
• Description: IC MCU 8BIT 8K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH8CTG

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 512Byte
• # I/os (max): 13
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO9S08SH8 - BOARD DEMO FOR MC9S08SH FAM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Appendix A Electrical Characteristics
A.12.3
Table A-15
312
1
2
3
4
5
and
SPI
Num
Maximum baud rate must be limited to 5 MHz due to input filter characteristics.
Refer to
All timing is shown with respect to 20% V
pins. All timing assumes slew rate control disabled and high drive strength enabled for SPI output
pins.
Time to data active from high-impedance state.
Hold time to high-impedance state.
10
11
12
1
2
3
4
5
6
7
8
9
Figure A-14
1
Figure A-14
D
D
D
D
D
D
D
D
D
D
D
D
C
Cycle time
Enable lead time
Enable lag time
Clock (SPSCK) high time
Clock (SPSCK) low time
Data setup time (inputs)
Data hold time (inputs)
Access time, slave
Disable time, slave
Data setup time (outputs)
Data hold time (outputs)
Operating frequency
through
through
Table A-15. SPI Electrical Characteristic
MC9S08SH8 MCU Series Data Sheet, Rev. 3
Rating
Figure A-17
Master and Slave
Master and Slave
Figure
3
4
2
A-17.
Master
Master
Master
Master
Master
Master
Master
Master
Slave
Slave
Slave
Slave
Slave
Slave
Slave
Slave
DD
describe the timing requirements for the SPI system.
and 70% V
Symbol
t
t
t
t
t
t
t
t
SCKH
SCKL
t
t
SI(M)
HI(M)
t
t
SI(S)
HI(S)
Lead
Lead
t
t
t
t
t
SCK
SCK
Lag
Lag
f
f
SO
SO
HO
HO
t
dis
op
op
A
DD
, unless noted; 100 pF load on all SPI
1/2 t
1/2 t
f
Bus
SCK
SCK
–10
–10
Min
1/2
1/2
30
30
30
30
25
25
dc
—
—
—
/2048
2
4
0
– 25
– 25
f
2048
Bus
Max
1/2
1/2
—
—
—
—
—
—
—
—
—
40
40
—
—
—
—
5
5
/4
Freescale Semiconductor
t
t
t
t
MHz
Unit
SCK
SCK
SCK
SCK
t
t
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
cyc
cyc