MC9S08RD32CDWE Freescale Semiconductor, MC9S08RD32CDWE Datasheet - Page 34

• Manufacturer Part Number: MC9S08RD32CDWE
• Description: IC MCU 32K FLASH 2K RAM 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08RD32CDWE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: S08RD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08RG60E
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Modes of Operation
I/O Pins
Memory
OSC — In any of the stop modes, the OSC stops running.
TPM — When the MCU enters stop mode, the clock to the TPM module stops. The modules halt
operation. If the MCU is configured to go into stop2 or stop1 mode, the TPM module will be reset upon
wakeup from stop and must be reinitialized.
ACMP — When the MCU enters any stop mode, the ACMP will enter a low-power standby state
compare operation will occur while in stop. If the MCU is configured to go into stop2 or stop1 mode, the
ACMP will be reset upon wakeup from stop and must be reinitialized.
KBI — During stop3, the KBI pins that are enabled continue to function as interrupt sources. During stop1
or stop2, enabled KBI1 pins function as wakeup inputs. When functioning as a wakeup, a KBI pin is
always active low regardless of how it was configured before entering stop1 or stop2.
SCI — When the MCU enters stop mode, the clock to the SCI module stops. The module halts operation.
If the MCU is configured to go into stop2 or stop1 mode, the SCI module will be reset upon wakeup from
stop and must be reinitialized.
SPI — When the MCU enters stop mode, the clock to the SPI module stops. The module halts operation.
If the MCU is configured to go into stop2 or stop1 mode, the SPI module will be reset upon wakeup from
stop and must be reinitialized.
CMT — When the MCU enters stop mode, the clock to the CMT module stops. The module halts
operation. If the MCU is configured to go into stop2 or stop1 mode, the CMT module will be reset upon
wakeup from stop and must be reinitialized.
Voltage Regulator — The voltage regulator enters a low-power standby state when the MCU enters any
of the stop modes unless the LVD reset function is enabled or BDM is enabled.
34
•
•
•
•
•
•
All I/O pin states remain unchanged when the MCU enters stop3 mode.
If the MCU is configured to go into stop2 mode, all I/O pin states are latched before entering stop.
Pin states remain latched until the PPDACK bit is written.
If the MCU is configured to go into stop1 mode, all I/O pins are forced to their default reset state
upon entry into stop.
All RAM and register contents are preserved while the MCU is in stop3 mode.
All registers will be reset upon wakeup from stop2, but the contents of RAM are preserved. The
user may save any memory-mapped register data into RAM before entering stop2 and restore the
data upon exit from stop2.
All registers will be reset upon wakeup from stop1 and the contents of RAM are not preserved. The
MCU must be initialized as upon reset. The contents of the FLASH memory are non-volatile and
are preserved in any of the stop modes.
MC9S08RC/RD/RE/RG Data Sheet, Rev. 1.11
Freescale Semiconductor
.
No