MC908AP64ACFAE Freescale Semiconductor, MC908AP64ACFAE Datasheet - Page 222

• Manufacturer Part Number: MC908AP64ACFAE
• Description: IC MCU 64K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64ACFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Core: HC08
• Processor Series: HC08AP
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 8 MHz
• Data Ram Size: 2 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Mounting Style: SMD/SMT
• Height: 1.4 mm
• Interface Type: SCI, SPI
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 7 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface Module (SPI)
13.12.5 CGND (Clock Ground)
CGND is the ground return for the serial clock pin, SPSCK, and the ground for the port output buffers. It
is internally connected to V
13.13 I/O Registers
Three registers control and monitor SPI operation:
13.13.1 SPI Control Register
The SPI control register:
SPRIE — SPI Receiver Interrupt Enable Bit
SPMSTR — SPI Master Bit
CPOL — Clock Polarity Bit
CPHA — Clock Phase Bit
222
•
•
•
•
•
•
•
•
This read/write bit enables CPU interrupt requests generated by the SPRF bit. The SPRF bit is set
when a byte transfers from the shift register to the receive data register. Reset clears the SPRIE bit.
This read/write bit selects master mode operation or slave mode operation. Reset sets the SPMSTR
bit.
This read/write bit determines the logic state of the SPSCK pin between transmissions. (See
Figure 13-4
identical CPOL values. Reset clears the CPOL bit.
1 = SPRF CPU interrupt requests enabled
0 = SPRF CPU interrupt requests disabled
1 = Master mode
0 = Slave mode
SPI control register (SPCR)
SPI status and control register (SPSCR)
SPI data register (SPDR)
Enables SPI module interrupt requests
Configures the SPI module as master or slave
Selects serial clock polarity and phase
Configures the SPSCK, MOSI, and MISO pins as open-drain outputs
Enables the SPI module
Address:
and
Reset:
Read:
Write:
Figure
SPRIE
$0010
Bit 7
0
13-6.) To transmit data between SPI modules, the SPI modules must have
SS
Figure 13-13. SPI Control Register (SPCR)
as shown in
= Unimplemented
MC68HC908AP A-Family Data Sheet, Rev. 3
R
6
0
SPMSTR
5
1
Table
13-1.
CPOL
4
0
CPHA
R
3
1
= Reserved
SPWOM
2
0
SPE
1
0
Freescale Semiconductor
SPTIE
Bit 0
0