C8051F062-GQR Silicon Laboratories Inc, C8051F062-GQR Datasheet - Page 194

• Manufacturer Part Number: C8051F062-GQR
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F062-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 59
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: 336-1214 - DEV KIT FOR F060/F062/F063
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

C8051F060/1/2/3/4/5/6/7
17.6. Timing
The timing parameters of the External Memory Interface can be configured to enable connection to
devices having different setup and hold time requirements. The Address Setup time, Address Hold time, /
RD and /WR strobe widths, and in multiplexed mode, the width of the ALE pulse are all programmable in
units of SYSCLK periods through EMI0TC, shown in Figure 17.6, and EMI0CF[1:0].
The timing for an off-chip MOVX instruction can be calculated by adding 4 SYSCLK cycles to the timing
parameters defined by the EMI0TC register. Assuming non-multiplexed operation, the minimum execution
time for an off-chip XRAM operation is 5 SYSCLK cycles (1 SYSCLK for /RD or /WR pulse + 4 SYSCLKs).
For multiplexed operations, the Address Latch Enable signal will require a minimum of 2 additional SYS-
CLK cycles. Therefore, the minimum execution time for an off-chip XRAM operation in multiplexed mode
is 7 SYSCLK cycles (2 for /ALE + 1 for /RD or /WR + 4). The programmable setup and hold times default
to the maximum delay settings after a reset.
194
Bits7-6:
Bits5-2:
Bits1-0:
EAS1
R/W
Bit7
EAS1-0: EMIF Address Setup Time Bits.
00: Address setup time = 0 SYSCLK cycles.
01: Address setup time = 1 SYSCLK cycle.
10: Address setup time = 2 SYSCLK cycles.
11: Address setup time = 3 SYSCLK cycles.
EWR3-0: EMIF /WR and /RD Pulse-Width Control Bits.
0000: /WR and /RD pulse width = 1 SYSCLK cycle.
0001: /WR and /RD pulse width = 2 SYSCLK cycles.
0010: /WR and /RD pulse width = 3 SYSCLK cycles.
0011: /WR and /RD pulse width = 4 SYSCLK cycles.
0100: /WR and /RD pulse width = 5 SYSCLK cycles.
0101: /WR and /RD pulse width = 6 SYSCLK cycles.
0110: /WR and /RD pulse width = 7 SYSCLK cycles.
0111: /WR and /RD pulse width = 8 SYSCLK cycles.
1000: /WR and /RD pulse width = 9 SYSCLK cycles.
1001: /WR and /RD pulse width = 10 SYSCLK cycles.
1010: /WR and /RD pulse width = 11 SYSCLK cycles.
1011: /WR and /RD pulse width = 12 SYSCLK cycles.
1100: /WR and /RD pulse width = 13 SYSCLK cycles.
1101: /WR and /RD pulse width = 14 SYSCLK cycles.
1110: /WR and /RD pulse width = 15 SYSCLK cycles.
1111: /WR and /RD pulse width = 16 SYSCLK cycles.
EAH1-0: EMIF Address Hold Time Bits.
00: Address hold time = 0 SYSCLK cycles.
01: Address hold time = 1 SYSCLK cycle.
10: Address hold time = 2 SYSCLK cycles.
11: Address hold time = 3 SYSCLK cycles.
EAS0
R/W
Bit6
Figure 17.6. EMI0TC: External Memory Timing Control
ERW3
R/W
Bit5
EWR2
R/W
Bit4
Rev. 1.2
EWR1
R/W
Bit3
EWR0
R/W
Bit2
EAH1
R/W
Bit1
SFR Address:
SFR Page:
EAH0
R/W
Bit0
0xA1
0
Reset Value
11111111