SAK-XE167FM-72F80L AA Infineon Technologies, SAK-XE167FM-72F80L AA Datasheet - Page 86
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAK-XE167FM-72F80L AA
Manufacturer Part Number
SAK-XE167FM-72F80L AA
Description
IC MCU 16BIT FLASH 144-LQFP
Manufacturer
Infineon Technologies
Series
XE16xr
Datasheet
1.SAF-XE167KM-48F80L_AA.pdf
(140 pages)
Specifications of SAK-XE167FM-72F80L AA
Core Processor
C166SV2
Core Size
16-Bit
Speed
80MHz
Connectivity
CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
Peripherals
I²S, POR, PWM, WDT
Number Of I /o
119
Program Memory Size
576KB (576K x 8)
Program Memory Type
FLASH
Ram Size
50K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 24x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
144-LFQFP
Data Bus Width
16 bit
Data Ram Size
32 KB
Interface Type
CAN, UART, SPI, I2S
Maximum Clock Frequency
80 MHz
Number Of Programmable I/os
119
Number Of Timers
5
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
2 (10 bit, 24 Channel)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
SP000628636
Table 12
Parameter
Absolute sum of overload
currents
External Pin Load
Capacitance
Voltage Regulator Buffer
Capacitance for DMP_M
Voltage Regulator Buffer
Capacitance for DMP_1
Operating frequency
Ambient temperature
1) Performance of pad drivers, A/D Converter, and Flash module depends on
2) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
3) Not subject to production test - verified by design/characterization.
4) An overload current (
5) This is the reference load. For bigger capacitive loads, use the derating factors from
6) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
7) To ensure the stability of the voltage regulators the EVRs must be buffered with ceramic capacitors. Separate
8) The operating frequency range may be reduced for specific types of the
Parameter Interpretation
The parameters listed in the following include both the characteristics of the XE167xM
and its demands on the system. To aid in correctly interpreting the parameters when
evaluating them for a design, they are marked accordingly in the column “Symbol”:
Data Sheet
exceeds the specified range:
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application.
Overload conditions must not occur on pin XTAL1 (powered by
adds to that pin’s leakage current (
defined by the overload coupling factor
polarity of the overload current that produces it.
The total current through a pin is |
voltage on analog inputs.
current may lead to increased delays or reduced driving capability (
buffer capacitors with the recomended values shall be connected as close as possible to each
the resistance of the board tracks below 2 Ω. Connect all
The minimum capacitance value is required for proper operation under all conditions (e.g. temperature).
Higher values slightly increase the startup time.
device designation (…FxxL). 80-MHz devices are marked …F80L.
Operating Condition Parameters (cont’d)
I
OV
) through a pin injects an error current (
V
Symbol
Σ|IOV|
C
C
C
f
T
OV
SYS
I
A
L
EVRM
EVR1
TOT
I
OZ
>
| = |
). The value of the error current depends on the overload current and is
V
IHmax
K
I
OZ
OV
XE167FM, XE167GM, XE167HM, XE167KM
| + (|
. The polarity of the injected error current is reversed from the
(
Min.
–
–
1.0
0.47
–
–
I
OV
I
> 0) or
OV
86
XE166 Family Derivatives / Base Line
| ×
K
Values
Typ.
–
20
–
–
–
–
OV
V
V
). The additional error current may distort the input
5)
OV
DDI1
<
pins together.
V
I
V
INJ
DDIM
ILmin
Max.
50
–
4.7
2.2
80
–
) into the adjacent pins. This error current
C
L
).
).
(
I
OV
XE167xM
< 0). The absolute sum of input
V
DDP
Unit Note /
mA
pF
μF
μF
MHz
°C
Electrical Parameters
.
Section
. This is indicated in the
Test Condition
3)
Pin drivers in
default mode
7)
One for each
supply pin
8)
V2.0, 2009-03
V
4.6.4.
DDI
pin to keep
7)
6)