AT90S8515A-8JI Atmel, AT90S8515A-8JI Datasheet - Page 48
![IC MCU 8K FLSH 8MHZ IT 44PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
AT90S8515A-8JI
Manufacturer Part Number
AT90S8515A-8JI
Description
IC MCU 8K FLSH 8MHZ IT 44PLCC
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheets
1.AT90S8515-4AC.pdf
(112 pages)
2.AT90S8515-4AC.pdf
(4 pages)
3.AT90S8515-4AC.pdf
(4 pages)
Specifications of AT90S8515A-8JI
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Converters
-
SS Pin Functionality
48
AT90S8515
Figure 35. SPI Master-slave Interconnection
The system is single-buffered in the transmit direction and double-buffered in the
receive direction. This means that bytes to be transmitted cannot be written to the SPI
Data Register before the entire shift cycle is completed. When receiving data, however,
a received byte must be read from the SPI Data Register before the next byte has been
completely shifted in. Otherwise, the first byte is lost.
When the SPI is enabled, the data direction of the MOSI, MISO, SCK and SS pins is
overridden according to Table 15.
Table 15. SPI Pin Overrides
Note:
When the SPI is configured as a master (MSTR in SPCR is set), the user can determine
the direction of the SS pin. If SS is configured as an output, the pin is a general output
pin, which does not affect the SPI system. If SS is configured as an input, it must be held
high to ensure master SPI operation. If the SS pin is driven low by peripheral circuitry
when the SPI is configured as master with the SS pin defined as an input, the SPI sys-
tem interprets this as another master selecting the SPI as a slave and starts to send
data to it. To avoid bus contention, the SPI system takes the following actions:
1. The MSTR bit in SPCR is cleared and the SPI system becomes a slave. As a
2. The SPIF flag in SPSR is set, and if the SPI interrupt is enabled and the I-bit in
Thus, when interrupt-driven SPI transmittal is used in Master Mode and there exists a
possibility that SS is driven low, the interrupt should always check that the MSTR bit is
still set. Once the MSTR bit has been cleared by a slave select, it must be set by the
user to re-enable SPI Master Mode.
When the SPI is configured as a slave, the SS pin is always input. When SS is held low,
the SPI is activated and MISO becomes an output if configured so by the user. All other
CLOCK GENERATOR
MOSI
MISO
result of the SPI becoming a slave, the MOSI and SCK pins become inputs.
SREG is set, the interrupt routine will be executed.
SCK
Pin
SS
See “Alternate Functions of Port B” on page 66 for a detailed description of how to define
the direction of the user-defined SPI pins.
SPI
Direction, Master SPI
User Defined
Input
User Defined
User Defined
MSB
8-BIT SHIFT REGISTER
MASTER
LSB
MISO MISO
MOSI MOSI
SCK
SS
V
CC
SCK
SS
Direction, Slave SPI
Input
User Defined
Input
Input
MSB
8-BIT SHIFT REGISTER
SLAVE
0841G–09/01
LSB