AT90S8515A-8JI Atmel, AT90S8515A-8JI Datasheet - Page 87
![IC MCU 8K FLSH 8MHZ IT 44PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
AT90S8515A-8JI
Manufacturer Part Number
AT90S8515A-8JI
Description
IC MCU 8K FLSH 8MHZ IT 44PLCC
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheets
1.AT90S8515-4AC.pdf
(112 pages)
2.AT90S8515-4AC.pdf
(4 pages)
3.AT90S8515-4AC.pdf
(4 pages)
Specifications of AT90S8515A-8JI
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Data Converters
-
Data Polling EEPROM
Data Polling Flash
0841G–09/01
4. If a Chip Erase is performed (must be done to erase the Flash), wait t
5. The Flash or EEPROM array is programmed one byte at a time by supplying the
6. Any memory location can be verified by using the Read instruction that returns
7. At the end of the programming session, RESET can be set high to commence
8. Power-off sequence (if needed):
When a byte is being programmed into the EEPROM, reading the address location
being programmed will give the value P1 until the auto-erase is finished and then the
value P2. See Table 31 for P1 and P2 values.
At the time the device is ready for a new EEPROM byte, the programmed value will read
correctly. This is used to determine when the next byte can be written. This will not work
for the values P1 and P2, so when programming these values, the user will have to wait
for at least the prescribed time t
34 for t
ming of addresses that are meant to contain $FF can be skipped. This does not apply if
the EEPROM is reprogrammed without first chip-erasing the device.
Table 31. Read Back Value during EEPROM Polling
When a byte is being programmed into the Flash, reading the address location being
programmed will give the value $7F. At the time the device is ready for a new byte, the
programmed value will read correctly. This is used to determine when the next byte can
be written. This will not work for the value $7F, so when programming this value, the
user will have to wait for at least t
erased device contains $FF in all locations, programming of addresses that are meant
to contain $FF can be skipped.
Part
AT90S8515
ing the third byte of the Programming Enable instruction. Whether the echo is
correct or not, all four bytes of the instruction must be transmitted. If the $53 did
not echo back, give SCK a positive pulse and issue a new Programming Enable
instruction. If the $53 is not seen within 32 attempts, there is no functional device
connected.
after the instruction, give RESET a positive pulse and start over from step 2. See
Table 34 on page 89 for t
address and data together with the appropriate Write instruction. An EEPROM
memory location is first automatically erased before new data is written. Use
Data Polling to detect when the next byte in the Flash or EEPROM can be writ-
ten. If polling is not used, wait t
See Table 35 on page 89 for t
data file(s) need to be programmed.
the content at the selected address at the serial output MISO (PB6) pin.
normal operation.
Set XTAL1 to “0” (if a crystal is not used).
Set RESET to “1”.
Turn V
WD_PROG
CC
power off.
value. As a chip-erased device contains $FF in all locations, program-
WD_ERASE
WD_PROG
WD_PROG
WD_PROG
WD_PROG
value.
before programming the next byte. See Table
before programming the next byte. As a chip-
value. In an erased device, no $FFs in the
before transmitting the next instruction.
P1
$80
AT90S8515
P2
$7F
WD_ERASE
87