AT90LS4433-4AI Atmel, AT90LS4433-4AI Datasheet - Page 70
![IC MCU 4K 4MHZ A/D LV 32TQFP](/photos/6/91/69154/313-32-tqfp_sml.jpg)
AT90LS4433-4AI
Manufacturer Part Number
AT90LS4433-4AI
Description
IC MCU 4K 4MHZ A/D LV 32TQFP
Manufacturer
Atmel
Series
AVR® 90LSr
Datasheet
1.AT90S4433-8AC.pdf
(126 pages)
Specifications of AT90LS4433-4AI
Core Processor
AVR
Core Size
8-Bit
Speed
4MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
4KB (2K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 6 V
Data Converters
A/D 6x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
32-TQFP, 32-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90LS4433-4AI
Manufacturer:
HYNIX
Quantity:
14
Part Number:
AT90LS4433-4AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Scanning Multiple
Channels
ADC Noise Canceling
Techniques
70
AT90S/LS4433
Since change of analog channel always is delayed until a conversion is finished, the
Free Run mode can be used to scan multiple channels without interrupting the con-
verter. Typically, the ADC Conversion Complete interrupt will be used to perform the
channel shift. However, the user should take the following fact into consideration: The
interrupt triggers once the result is ready to be read. In Free Run mode, the next conver-
sion will start immediately when the interrupt triggers. If ADMUX is changed after the
interrupt triggers, the next conversion has already started and the old setting is used.
Digital circuitry inside and outside the AT90S4433 generates EMI, which might affect
the accuracy of analog measurements. If conversion accuracy is critical, the noise level
can be reduced by applying the following techniques:
1. The analog part of the AT90S4433 and all analog components in the application
2. Keep analog signal paths as short as possible. Make sure analog tracks run over
3. The AVCC pin on the AT90S4433 should be connected to the digital V
4. Use the ADC Noise Canceler function to reduce induced noise from the CPU.
5. If some Port C pins are used as digital outputs, it is essential that these do not
Figure 49. ADC Power Connections
Note that since AVCC feeds the Port C output drivers, the RC network shown should not
be employed if any Port C serve as outputs.
should have a separate analog ground plane on the PCB. This ground plane is
connected to the digital ground plane via a single point on the PCB.
the analog ground plane and keep them well away from high-speed switching
digital tracks.
voltage via an LC network as shown in Figure 49.
switch while a conversion is in progress.
28
27
26
25
24
23
22
21
20
19
PC5 (ADC5)
PC4 (ADC4)
PC3 (ADC3)
PC2 (ADC2)
PC1 (ADC1)
PC0 (ADC0)
AGND
AREF
AVCC
PB5
100 nF
VCC
1042H–AVR–04/03
CC
supply