ATTINY15L-1PC Atmel, ATTINY15L-1PC Datasheet - Page 37
![IC AVR MCU 1K FLASH 2.7V 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
ATTINY15L-1PC
Manufacturer Part Number
ATTINY15L-1PC
Description
IC AVR MCU 1K FLASH 2.7V 8DIP
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY15L-1PC
Core Processor
AVR
Core Size
8-Bit
Speed
1.6MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Eeprom Size
64 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Ram Size
-
Connectivity
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
The EEPROM Control Register
– EECR
1187H–AVR–09/07
• Bit 7..4 – RES: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
• Bit 3 – EERIE: EEPROM Ready Interrupt Enable
When the I-bits in SREG and EERIE are set (one), the EEPROM Ready Interrupt is
enabled. When cleared (zero), the interrupt is disabled. The EEPROM Ready Interrupt
generates a constant interrupt when EEWE is cleared (zero).
• Bit 2 – EEMWE: EEPROM Master Write Enable
The EEMWE bit determines whether setting EEWE to one causes the EEPROM to be
written. When EEMWE is set (one), setting EEWE will write data to the EEPROM at the
selected address. If EEMWE is zero, setting EEWE will have no effect. When EEMWE
has been set (one) by software, hardware clears the bit to zero after four clock cycles.
See the description of the EEWE bit for an EEPROM write procedure.
• Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal – EEWE – is the write strobe to the EEPROM. When
address and data are correctly set up, the EEWE bit must be set to write the value in to
the EEPROM. The EEMWE bit must be set when the logical “1” is written to EEWE, oth-
erwise no EEPROM write takes place. The following procedure should be followed
when writing the EEPROM (the order of steps 2 and 3 is not essential):
1. Wait until EEWE becomes zero.
2. Write new EEPROM address to EEAR (optional).
3. Write new EEPROM data to EEDR (optional).
4. Write a logical “1” to the EEMWE bit in EECR.
5. Within four clock cycles after setting EEMWE, write a logical “1” to EEWE.
Caution: An interrupt between step 4 and step 5 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the
EEPROM is interrupting another EEPROM access, the EEAR or EEDR Register will be
modified, causing the interrupted EEPROM access to fail. It is recommended to have
the Global Interrupt Flag cleared during the four last steps to avoid these problems.
When the write access time (typically 5.1 ms if the internal RC Oscillator is calibrated to
1.6 MHz) has elapsed, the EEWE bit is cleared (zero) by hardware. The user software
can poll this bit and wait for a zero before writing the next byte. When EEWE has been
set, the CPU is halted for two cycles before the next instruction is executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the
correct address is set up in the EEAR Register, the EERE bit must be set. When the
EERE bit is cleared (zero) by hardware, requested data is found in the EEDR Register.
The EEPROM read access takes one instruction and there is no need to poll the EERE
bit. When EERE has been set, the CPU is halted for four cycles before the next instruc-
tion is executed.
Bit
$1C
Read/Write
Initial value
R
7
–
0
R
6
–
0
R
5
–
0
R
4
–
0
EERIE
R/W
3
0
EEMWE
R/W
2
0
EEWE
R/W
X
1
ATtiny15L
EERE
R/W
0
0
EECR
37