ATTINY15L-1PC Atmel, ATTINY15L-1PC Datasheet - Page 46
![IC AVR MCU 1K FLASH 2.7V 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
ATTINY15L-1PC
Manufacturer Part Number
ATTINY15L-1PC
Description
IC AVR MCU 1K FLASH 2.7V 8DIP
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY15L-1PC
Core Processor
AVR
Core Size
8-Bit
Speed
1.6MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Eeprom Size
64 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Ram Size
-
Connectivity
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
ADC Noise Canceler
Function
The ADC Multiplexer Selection
Register – ADMUX
46
ATtiny15L
The ADC features a noise canceler that enables conversion during ADC Noise Reduc-
tion mode (see “Sleep Modes” on page 23) to reduce noise induced from the CPU core
and other I/O peripherals. If other I/O peripherals must be active during conversion, this
mode works equivalently for Idle mode. To make use of this feature, the following proce-
dure should be used:
1. Make sure that the ADC is enabled and is not busy converting. Single Conver-
2. Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a conver-
3. If no other interrupts occur before the ADC conversion completes, the ADC inter-
• Bits 7..6 – REFS1..REFS0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in Table 19. If these bits
are changed during a conversion, the change will not go into effect until this conversion
is complete (ADIF in ADCSR is set). Whenever these bits are changed, the next
conversion will take 25 ADC clock cycles. If active channels are used, using AVCC or an
external AREF higher than (AVCC - 1V) is not recommended, as this will affect ADC
accuracy. The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 19. Voltage Reference Selections for ADC
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data
Register. If ADLAR is cleared, the result is right-adjusted. If ADLAR is set, the result is
left-adjusted. Changing the ADLAR bit will affect the ADC Data Register immediately,
regardless of any ongoing conversions. For a complete description of this bit, see “The
ADC Data Register – ADCL and ADCH” on page 49.
Bit
$07
Read/Write
Initial Value
REFS1
sion mode must be selected and the ADC conversion complete interrupt must be
enabled.
ADEN = 1
ADSC = 0
ADFR = 0
ADIE = 1
sion once the CPU has been halted.
rupt will wake up the MCU and execute the ADC conversion complete interrupt
routine.
0
0
1
1
REFS0
0
1
0
1
REFS1
R/W
7
0
Voltage Reference Selection
V
External Voltage Reference at PB0 (AREF) pin, Internal Voltage
Reference turned off.
Internal Voltage Reference without external bypass capacitor,
disconnected from PB0 (AREF).
Internal Voltage Reference with external bypass capacitor at PB0 (AREF)
pin.
CC
REFS0
R/W
used as analog reference, disconnected from PB0 (AREF).
6
0
ADLAR
R/W
5
0
R
4
–
0
R
3
–
0
MUX2
R/W
2
0
MUX1
R/W
1
0
MUX0
R/W
0
0
1187H–AVR–09/07
ADMUX