LPC2106FHN48,551 NXP Semiconductors, LPC2106FHN48,551 Datasheet - Page 2

• Manufacturer Part Number: LPC2106FHN48,551
• Description: IC ARM7 MCU FLASH 128K 48-HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2106FHN48,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
• For Use With: 622-1019 - BOARD FOR LPC2106 48-LQFP622-1008 - BOARD FOR LPC9103 10-HVSON568-1756 - BOARD EVAL FOR LPC210X ARM MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Other names: 568-1324; 935274661551; LPC2106FHN48-S

NXP Semiconductors
3. Ordering information
LPC2104_2105_2106_7
Product data sheet
I
I
I
I
I
I
I
I
I
I
I
I
I
Table 1.
Type number
LPC2104BBD48
LPC2104FBD48/00
LPC2104FBD48/01
LPC2105BBD48
LPC2105FBD48/00
LPC2105FBD48/01
LPC2106BBD48
LPC2106FBD48
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or
full chip erase takes 400 ms.
Vectored Interrupt Controller with configurable priorities and vector addresses.
EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service
routines can continue to execute whilst the foreground task is debugged with the
on-chip RealMonitor software.
Embedded Trace Macrocell enables non-intrusive high speed real-time tracing of
instruction execution.
Multiple serial interfaces including two UARTs (16C550), Fast I
SPI.
Two 32-bit timers (7 capture/compare channels), PWM unit (6 outputs), Real Time
Clock and Watchdog.
Up to thirty-two 5 V tolerant general purpose I/O pins in a tiny LQFP48 (7 mm
package.
60 MHz maximum CPU clock available from programmable on-chip Phase-Locked
Loop with settling time of 100 s.
The on-chip crystal oscillator should have an operating range of 1 MHz to 25 MHz.
Two low power modes, Idle and Power-down.
Processor wake-up from Power-down mode via external interrupt.
Individual enable/disable of peripheral functions for power optimization.
Dual power supply:
N
N
CPU operating voltage range of 1.65 V to 1.95 V (1.8 V
I/O power supply range of 3.0 V to 3.6 V (3.3 V
Ordering information
Package
Name
LQFP48
LQFP48
LQFP48
LQFP48
LQFP48
LQFP48
LQFP48
LQFP48
Rev. 07 — 20 June 2008
Description
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
plastic low profile quad flat package; 48 leads;
body 7
7
7
7
7
7
7
7
7
1.4 mm
1.4 mm
1.4 mm
1.4 mm
1.4 mm
1.4 mm
1.4 mm
1.4 mm
LPC2104/2105/2106
Single-chip 32-bit microcontrollers
10 %) with 5 V tolerant I/O pads.
8.3 %).
2
C-bus (400 kbit/s), and
© NXP B.V. 2008. All rights reserved.
Version
SOT313-2
SOT313-2
SOT313-2
SOT313-2
SOT313-2
SOT313-2
SOT313-2
SOT313-2
7 mm)
2 of 41